I once had this problem with AF 3260C where an oversight joined the firmware update package from the machine an SR that was not installed. The SR firmware is placed wrong and the machine detected it...
Type: Posts; User: Ramón
I once had this problem with AF 3260C where an oversight joined the firmware update package from the machine an SR that was not installed. The SR firmware is placed wrong and the machine detected it...
What result can give you is to connect the MP C 6501 to SR 5000 to be detected and will install the firmware. Once done reinstall the SR 4030 I do not think you need to change any motherboard.
Maybe it's a mechanical problem. I had a similar problem and in the end the solution was to move down the line the pad sponges prevention. Look at this picture.
25044
Check the thermostat pressure roller can be wide open or bad fuser connector.
I think you can also think that the pump has too much air inside and not suck either toner. You can try to manually fill toner reaches the tube using a syringe pump to the vacuum to the pump and try...
I think a solution that can give your client is that the page is only in black black, with no character or color point and if you have photos or drawings grayscale them, that way even in the driver...
Remove the upper right side cover, sure to be stained with toner inside. Locate the laser unit and on its left side you will see the timing plate. Take it off and clean it very carefully, it sure is...
In the new stapler unit you put Guide - Standard Fence previous unit? if you put this can happen you say
On the other hand, if the same phenomenon with both staple units maybe the problem is not...
You can choose from different types of fax reception and one of them is forward and store. It is quite possible that you have selected this mode. Before you can configure forwarding and storing only...
I'm using this cutting tool:
JCB 250mm Aviation Tin Snip Right Cut, 28507512
With a little careful not to touch the toner pump, cutting is fast and accurate.
Does anyone have information on this utility?
I have read that when the boot program Flash ROM is damaged or corrupted, the SD card can be used to start the machine and download the firmware to...
Perhaps after all is somewhat simpler as for example a failure of the sensor positioning of the pressure roller. See page 313 of the service manual.
I wonder if this new site is designed competition. In this age of information instead of going forward we think back.
The engineer or group of engineers who designed TESSA should give my-ricoh...
Tebow83 I remember the fault as quite ungrateful, after reviewing everything I said in the previous section and have followed the instructions given to the service manual, gave me no result. I...
Check the thermostat pressure roller with a multimeter and if the lamp, the thermostat and termitor are OK, replace the Fuser harness (Ref: B2374305).
Hello George: You're going to fix by replacing the roller PTR.
The problem is cleaning the ITB. Change this piece D0296027 CLEANING UNIT:INTERMEDIATE TRANSFER:ASS'Y.
Good luck
Look at the drive unit in the rear of the machine. It is possible that the large white pinion has some expansion and cause the deviation or it may be that in a visit that pinion is turned upside down...
To all those good ideas to solve this code I think you should also check these pieces Bushing AE03 1065: Fusing Sub-unit and also clean the vent fuser will probably be full of dust.
PS Does option? Have you used the RPCS driver if not already? In the latter case you can use any profile that gives the driver to suit the kind of impression that you requested by the client.
In which of the two is the problem? If the 700K I would look for clutch block revealing. Just remove the top cover on the right side you see at the top. If you see rust off will need to replace or...
Are they red or magenta?
Can you post a picture?
¿Son rojas ó magenta?
Look this:
Shorted 24 V fuse on the PSU
Teebee1234: Your point of view that's fine. I still think the problem is in the PCU Y. The back of the Unit Charge is removed from the site and the tabs that engage the block are not well placed PCU...