Magenta and yellow are smearing lead to trail towards the center of copies & prints.
Replaced both IU's, transfer belt and transfer roller. black and cyan are fine.
Any ideas? I'll attach...
Type: Posts; User: dqydj
Magenta and yellow are smearing lead to trail towards the center of copies & prints.
Replaced both IU's, transfer belt and transfer roller. black and cyan are fine.
Any ideas? I'll attach...
anyone had any luck with the ir2525 faxing over a voice over IP connection.
Tried everything I can think of but it just doesn't work. Customer has a brother
mfp that sends and receives just fine...
I agree with lagonda.
Mita and their ungrounded heat sinks.
To this day I can't have my cell phone on vibrate
without jumping out of my skin when it vibrates.
I've gotta wonder if he opened the left and right doors before
removing the transfer belt or just the left door.
If just the left that would explain the breaking up of the
belt unit since the...
This model has 3 different firmware files and depending on which
printer expansion kit you are using will tell you which firmware file
to use.
if you flash the machine with the wrong firmware...
You might try removing the op panel and make sure the
4 pin ribbon cable for the touch glass hasn't come loose.
If that's not the case I agree, replace the touch glass.
I work for oce' imagistics and at this point or at least the last time
I checked the level 3.01 firmware was still in test mode and
not readilly available yet for the imagistics machines.
I could...
I live down the street from a coke distibuter and they have vending
machines at the gate that charge 25 cents for a 12 ounce can and
50 cents for a 20 ounce bottle here in spokane washington....
The Mita dc111 was a great little box. The only weak spot was the
platen clutch pack. when they got older they would bind up and
drive the platen to the left or right depending which clutch bound...
thud
click
About 15 years ago we had a lady call in to say her fax would
recieve but she couldn't get it to send.
The tech went out and faxed something to our office and we
recieved it fine. when he had her...
laser code.
it's either the laser the A board or the power supply.
Most likely the laser
Hold down the USER PRESET original size LEDGER and the 3 key
simultaneously.
If this is done correctly the display should show F1.
press the 5 key and press print.
Enter 42 and press print....
I'm confused?
Which is still working? The machine with the LCT or the one
with the 2 drawer base?
Both machines?
I'm lost...
developer is the carrier for the toner.
in other words when your machine adds toner it is mixing toner into the developer and it will add toner until the mixture is correct.
DON'T put developer...
We still have a lot of these out there as well.
What I would look at is wear on the actuator of the paper feed
switches. I've seen these cause eratic jamming.
As old as these machines are there...
Our portland oregon office bought the burner for these chips.
We send the chips there to be reprogramed and they work
great. we are getting twice the yield out of the image units.
are you talking about the admin password for the copier or the fiery?
145.00 an hour plus travel time.
spokane washington
mita, panasonic, toshiba, sharp, konica/minolta, muratec, brother,
and savin
I'm working on a savin 2522 that only from a cold power up throws a
sc-542 code which is a fuser temp warm-up error.
the fuser temp does not reach the stand-by temp within 20 seconds
after the...
I have my wireless router running with a comcast cable modem.
It's been over a year since I set it up so I don't know how much help
I'll be.
The setup I have running is a computer in the basement...
This code is a hardware time-out.
What I've got going on is when I go into service mode
and then state conformation and run a check on the memory
the work memory checks fine but the two file...
Allright I'll give you tha gandhi one but the rest....DAMN!!!!