Hi,
Would like to get some input on this copier Ricoh MP C6003 output.
The output looks like it's not fully transferring to the paper. It's on all colors.
I've replaced the drums and the...
Type: Posts; User: Oscar57
Hi,
Would like to get some input on this copier Ricoh MP C6003 output.
The output looks like it's not fully transferring to the paper. It's on all colors.
I've replaced the drums and the...
Hi,
Is there an adjustment for controlling the speed that the shift tray goes down?
I'm running 100lb. cover and it not staying under the bottom foot.
Hi,
I have a BK5030 booklet maker being used as a stand alone.
When started the screen does not react to touch. Tried multiple restarts
and the screen will display different screens. It's feels...
I did already clean the ID sensors. It seems like it needs more transfer voltage but I don't know if that's adjustable.
I guess the next thing is to change the transfer belt assy.
Hi,
Does anyone know if there is a toner transfer adjustment or quality adjustment on the Ricoh C6003? Replaced drums and developers but the screens and solids are not that great.
The Ricoh SP C...
Hi,
I'm having the same exact problem. Did you ever find out what was causing this to happen?
Hi,
I have a Fiery E-22B that stopped working. Tell it to print a built in PS test page or print a file to it from Command Workstation and the print job shows printing but doesn't print. So I am...
Hi,
Could someone please confirm the SP Mode login. I can't login so I'm thinking it might be locked?
- Thanks:)
Yes it has about 2 years.
- Thanks again
OK, The manual states a flashing #4 equals failed NVM memory. The battery that holds the settings is supposed to be a minimum of 2.7 volts. My reading is .5 volts. So I am going to replace the...
I'm sorry I mainly work on Konica's. The slide out draw where I replaced the hard drive has a LED on the outside of the draw and it flashes between a number 4 and a U symbol. Is that what your...
I just replaced hard drive and did re-altbooting. But it still does not boot up to a ready state.
Hi,
I have a Xerox 9303 that won't boot up. After an 1 hour it still states "Please Wait ... The System Is Restarting". I have done a Altboot Software Upgrade which updates the Copy controller and...
Hi,
I am having a problem with toner cartridges being reported by the printer as empty after a couple hundred prints. OEM and aftermarket. I cleaned the contacts that the toner cartridge touches...
Hi,
Does anyone know if the Fiery IC-414 off of the Bizhub C454-C554 will also work on the Bizhub C754 - C654? And is the video interface card V-506 different.
- Thanks
Flash,
You were right. One of the plastic couplers is cracked. I tried looking up that part # on the Web and I came up empty. Do you know where I can purchase these couplers?
- Thanks Mark
Hi,
Does anyone know if there is a adjustment for Fuser temperature on the Xerox Phaser 7800. I am having a issue with toner sticking to the paper. If I run a much heavier paper stock setting the...
Hi,
I looked at the Colorqube. And then the service manual and I can't see or find a coupler listed. Would you happen to know the part number? All the supporting brackets around the printheads...
Hi Exok,
I tried to perform the dc972 like you suggested and a prompt came up telling me I had to do the dc971 first. So I started that and after a couple of minutes I got this error "Set...
Thanks Exok,
I'll make sure I follow your instructions.
Flash,
Do you know if all 4 colors are the same printhead: part number?
Hi,
I have a Xerox Colorqube 9303 with non printing jets. It is just in the cyan. I've cleaned the jets multiple times with some slight improvement. If anyone could tell me the steps that they...
Hi,
Does anyone know if it is possible to turn off the center staple feature when using a PI-505 Post Inserter and doing a half-fold for finishing off line?
Hi,
Does anyone know if there is a way to adjust the Front to Back image density on the C652? It is happening on the Magenta unit. Density is much lighter going towards the last 4 inches of the...
Thanks for the Pad part number. Does anyone have the part numbers for the actual Cleaning Wand?