I also had the similar fault, at the first run when the machine is ON it will give an error after leaving as is for 30 minutes and POPO again it will be ready and works alright. I tried wiping and...
Type: Posts; User: rukshan4u2c
I also had the similar fault, at the first run when the machine is ON it will give an error after leaving as is for 30 minutes and POPO again it will be ready and works alright. I tried wiping and...
Thanks for posting onbehalf, well followed the steps that you have listed where can i find the Scan Manager option and what is the default password for System Settings / System Manager ID does the...
Hi,
Please be kind enough to instruct me how to configure IR 2520 scanning option to a windows network via TCP / IP.
:)
Hi,
Im getting an error F110 in Toshiba E Studio 351C while I make it power On for the day. Once its been left On with the error code for 15~20mins and power off - on the copier start alright, I...
Error Code SC34-08 appeared while machine was working. Now error just appears when powered on. What does this code means. How can i reset this
Thanks in advance.
Can u please help me with the code to reset the counter of developer because it halted working due to this error. Please..
:(:(:(
How can i find the chips for the developer in the IU. I found some chips attached to the drum but i couldnt find the chips in the developer unit please help...is there a specific code to reset this...
Hi,
I'm getting an error message displayed to replace Developer for magenta & yellow, and i need to reset the developer counter so that will eliminate the error message. Picture of the message...
Hi..
Recently I have been getting error code CE40 then i resetted m/c using 08 - 665 / 08 -203 value to "0"
OR by clearing the codes using 08 - 573 to 576 to "0" .
Sometimes i have seen 08-576 (k)...
hi,
I was adjusting the copy quality in my 351c by cleaning the internal process (Transfer belt, Charge wires, Drum blade, dev units, lazer optics etc., after successfull service i made several...
Here again Michael C is correct... F100~F108 faults are related to HDD faults. Check the data cables, Run 3 , C, Power On procedures if not replace HDD & Firmware
Mic C is right remove the drum and transfer unit check for the cleaning blades.
Power Off first
Power on pressing 03
you will be on Dignostic Output test mode
make sure all covers are closed
Enter 109--------Observe PFP Motor runs ok.
Enter 225--------Observe...
estudio 282 series as far i know its supporting upto 40GB only, 80GB will work alright it will detect from the mainboard but it will act as a 40GB Hdd. therefore u will not gain extra space as...
I assume that inside the Dev unit there might be some fault with the spirals that will circulate dev both ways, best thing is to remove all dev from the unit and inspect the movement inside....
Power On machine holding "c" & 3 key then u can follow the screen instructions, if u got the firmware save it to a pendrive and insert it to the machine. partitioning and formatting will done in that...
Cant u attach a sample copy took from the printer
Hey estudio 28 series will support upto 80gb and 35/45 series goes upto 160GB. but u will have to install the firmware on the new hard drive to make ur machine at work. if can clone the firmware from...
Check the transfer belt, if can remove the transfer belt inside the transfer belt u will find two shafts remove those shafts and clean them until u get a shinning surface (dont sandpaper) some times...
I'll give this a try and get back to you soon. THanks bro....
Basically the EStudio 351C comes with 1 & 2 trays on it. 3 & 4 trays will be optional (known as PFP) anyway in my system i got the 3rd tray. As u advised i have already checked the spring tension on...
Hi
I removed all the clutches replaced with working ones, a small wheel with needle razors(Turning one direction only), all sensors and actuators, PFP tray main motor, PCB Tray module. Still the...
Hi,
Please tell me whether PFP Drawer Unit for estudio 351c is compatible with estudio 282 PFP Drawer units.
And estudio 282 PFP Drawer Unit (Entire Unit) can be used in Estudio 351c Machine.
It seems to me all the machines & pc's are been removed it's covers,.. I guess you will take ages to put all these machines to work.. surely you will have to organise in your stuff and get someone to...
In Colombo, Sri Lanka all copier brand techs are given mobikes some travel to customers in buses. So when they reach customers they are full of sweat its awful when travel on dusty roads. The same...