Search:

Type: Posts; User: michaelc

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    3,292

    [Jamming] Re: MX-6070N with MX-FN28 - FNRMDLT

    Have the foam rollers been removed from the exit/delivery unit during set up ?
  2. Replies
    4
    Views
    1,098

    Re: Dropout on duplex

    When we refurb these fuser units its the inlet guide is replaced as they get in a bad state.
  3. Replies
    8
    Views
    1,583

    Re: Mxm 753 strange copy on duplex

    Could always take it out and clean it first to
  4. Thread: 453 turn 452

    by michaelc
    Replies
    3
    Views
    721

    Re: 453 turn 452

    Always wondered if that would work.
  5. Thread: MX-FN22

    by michaelc
    Replies
    9
    Views
    4,609

    Re: MX-FN22

    There is a new mod getting tested on the sensors which cause the code. It uses the pressure rollers for the reference as some one has said. There is a little piece of plastic which is fitted over the...
  6. Thread: MX-FN22

    by michaelc
    Replies
    9
    Views
    4,609

    Re: MX-FN22

    Please dont bend this plate, make things a lot worse.
  7. Replies
    13
    Views
    8,159

    [Jamming] Re: Mxm565 build up on fuser guide

    Just my 2 pence (im english) a lot of people dont clean the dev filters on the black and white machines.
    If its high volume you can sometimes get to stage where the guides can loose the curvature...
  8. Replies
    16
    Views
    27,924

    [Error Code] Re: H4-02 on MX-3060/MX-6070/MX-5070

    Before you replace the fuser or put it back on the machine after a rebuild (or even take it out of the machine) you should (dont' quote me on this exactly) reboot the machine without the fuser in...
  9. Replies
    10
    Views
    2,049

    Re: Color Calibration

    I wish everyone did this, i just tend to use the customers paper. New machines have 61-11 to compensate for the laser.
  10. Replies
    7
    Views
    1,541

    [Misc] Re: Sharp Car Inventory

    We carry car stock so i can be out in the field without stocking up for as long as possible. Parts are logged to the call and if its a which i have on my template it will be automatically replenished...
  11. Replies
    11
    Views
    3,129

    Re: MX5141 drum/developer issue

    are you using first of all genuine sharp kit. Are you using the MX310MK or MX510MK kits?
  12. Replies
    6
    Views
    1,264

    Re: MX5112 Dev Tank

    Thanks for posting the fix. Will keep it in mind.
  13. Replies
    12
    Views
    1,867

    [CQ] Re: E-Studio 3520C

    5665165212
  14. Replies
    9
    Views
    7,287

    Re: Sharp MX-C311 L4-16

    This has happened to me once. Would check for a unicorn in the ADF.
  15. Replies
    8
    Views
    2,837

    Re: MX2314 - please wait

    It happens on a few sharps. I keep an image of each SD on my laptop for this. Happy you fixed.
  16. Thread: MXM354 F1-15

    by michaelc
    Replies
    3
    Views
    938

    Re: MXM354 F1-15

    Expensive fix, but it worked
  17. [Electrical] Re: mx-m354n Blank image but drum covered with toner No codes

    Is the laser working?
  18. Replies
    5
    Views
    1,225

    Re: Isn't this just the best fun.

    Sharp fuser units are not that bad. They are all the same give or take (lamps, webs, etc).

    I see a lot of people people changing whole fuser units because they are so cheap.
  19. Replies
    17
    Views
    1,963

    Re: MX-M503 Prints fine, won't copy

    I still try to educate end users, although after more than ten years of doing it I am hoping just once that one person will take notice as it feels like I would have more luck with making a cup of...
  20. Replies
    3
    Views
    3,272

    [Error Code] Re: Toshiba ES 755 CB10 Finisher error

    These finishers have been used for a while, was usually the cam white with a blue one way bearing in which failed.
  21. Thread: developer

    by michaelc
    Replies
    6
    Views
    1,061

    [CQ] Re: developer

    Is the mag roller the smooth or ridged?
  22. [Error Code] Re: Toshiba E Studio 18 error - TIME FOR MAINTENANCE

    Do the maintenance and reset the codes for it
  23. Replies
    4
    Views
    640

    Re: toshiba E-351c operation panel frozen

    Format the hard drive and update the firmware
  24. Replies
    6
    Views
    960

    Re: change m toner

    Are you using genuine sharp toner cartridges? Just to get that awkward question out of the way
  25. Replies
    17
    Views
    1,963

    Re: MX-M503 Prints fine, won't copy

    I wonder if some one has messed around with some settings and then put them back? Hope this one is an easy fix. Let us know how it goes
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4