If the machine has trays 3 and 4,make sure bottom right hand door is closed properly. I have seen this on mpc machines before. It just sits saying replace toner but does nothing even when a new...
Type: Posts; User: GC-SCO
If the machine has trays 3 and 4,make sure bottom right hand door is closed properly. I have seen this on mpc machines before. It just sits saying replace toner but does nothing even when a new...
See if your second team can help you:D
I have cleaned all sensors and no reflective plates. I have also cleaned all rollers as well as replacing feed belt,roller and dfp.
All other sizes A3 - A4 work fine. It jams solely on A4 r.
its a DF3010...
Hi there, Im looking for some input into a wierd fault. I have an MPC 4000 which will run A4r and A3 all day long but will struggle to get through a pile of 20 A4r on the DF. It shows 005 DF jam...
Generally what happens is the scanner motor fails causing the formatter to go. What we found in the early days of working on these is we would replace the scanner then have to replace the formatter...
update the firmware to the latest level also. If the machine is less than a year old HP should cover this with a warranty.
Sorry to be the bearer of bad news.
you will more than likely have to replace the formatter aswell. When the scanner motor fails it tends to take out the formatter. Have had to do this loads of times
I have a mpc2500 which blurrs the last 3rd of the image only on A3 from the glass. If I lift up
the left front corner of the scanner when copying this reduces but does not clear completely.
Does...
Do they supplt parts for other HP machines as well ?
utility/counter/details/stop,0,0,stop,0,1. press in that order ,that should do the trick:)
You will most likely need a tech. These lines are usually caused by faulty/dirty drum units...
Has anyone had an issue with untidy exit when using offset sort on above machine? I have one with just over 1 million copies and the stacking on exit is very untidy. Any help appreciated
Update the firmware, which you can download from HP.COM. If you have no joy change the formatter board. Cures most faults on most Hp machines. If the machine is less than a year old It is under...
Replace all the rollers in the duplex section as a set. I would also replace the flags while you are in there as its a bit of a strip down to replace the rollers anyway.
Replace the sensor flags in the duplex section as they wear down. This causes probs on A4 first. Also clean the bushings on the white idle roller which sits on the left hand side of the inversion...
clean or replace the ozone filters. They are usually filthy and cause the machine to overheat. Easy way to tell is do single copies and they should be ok. Then do a run of around 100 your copies...
Have a brand new c353 that I cant browse through internet explorer on customers desktop. I can ping from desktops and print to it no problem but when I browse the machine i get a blank screen. I can...
cheers Guys. It turned out to be shift motor causing the problem. I had already done the firmware with no joy. fitted motor and no jams for over 20k. thanks for your info anyway.:)
Hi Folks I was wondereing if anyone has come accross this problem. I currently have aproblem where the machine jams very intermittantly showing a 131 finisher jam about 3 times in 8000 copies....
Hi folks does anyone know how to print off a protocol trace report on either a 8360p or a 1020e.Other than that anyone know where I can get a service manual for either of these.Dont really want to...
cheers Random I did it your way and it seems to be okay. Does seem kinda slow though any other ideas
thanks for that I will give it a try. I had been trying to add it to desktops in the usual way,ut it would not print.I had downloaded the driver from browsing the Creo through my address bar though.
Hi folks does anyone have experience on setting up one of these up. I have fitted to a c5500 after upgrading the firmware on it.It prints on its own to the machine but I am having problems installing...
Fitted new prom to finisher.Cant beleive I didn't think to do m/c:eek:.M/c does work fine without finisher though and message actualy comes up before paper has even reached finisher.Will try m/c...