Search:

To View
MODE LIST > COPIER > DISPLAY > JAM


To print
COPIER > Function > MISC-P > HIST-PRT


Hope that helps

All three Cyan, Yellow, & Magenta drums where replaced, cleared up all the dots and spots!

Thanks again Blackcat for your time and guidance! And yes Taggerung we didn't find any aftermarket drums,...

Blackcat thanks!

Looks like my boss has drums coming in soon, not cheap.

I havent connected PCRs to arcing on drums before, is that comon on these model? Any way to prevent that in the future?...

Hi Folks,

Got a Kyocera TaskALFA 300CI with magenta, cyan, & yellow spots on prints, happens on color prints only. (See attached pics) Pulled the drums out, cleaned & coated them along with the...

tmaged, that makes sense now, I suspected it be a new fuser but couldn't confirm it. Fuser was put in by a previous dealer who probably don't do sharps very often. It somehow ran with no pressure...

ZOOTECH & igi,

Next trip you guys are near D.C./Maryland let me know, I owe you guys drinks!

I corrected the pressure screws, the coated screws, and the jamming has stopped. Sharp seems to be...

Thanks igi!
I released the tension completely and now have both rollers turning with resistance now by hand. Are the screws supposed to be turned all the way counter clockwise and free turning...

Hello Folks,

Got a Sharp MX-M550U jamming at the fuser every copy. It gets about 15mm before throwing a jam POD1_N. I ran the sensor override in Sim mode and it still jams in the exact spot, so I...

Yeah my inclination is its the registration assy. I'm looking at the PC and making a list of parts I need.

Slimslob do you happen to have a cheat sheet for part numbers to order for the reg and...

Thanks for reminding me. Yes, with fresh paper, we ran jobs out of all the other trays including the by-pass and the same problem occurs. Because of that, I focused in the processing area only.

I...

Been back several times, I back tracked everything I handled on the PM. re-seated the developer, re-seated the transfer belt, re-seated the drum unit. I'm not finding anything blatantly out of place....

Hi Folks, I've got this Ricoh 1075 shooting skew images.

I rebuilt the drum, developer, and transfer unit. After completing the PM, I starting noticing a crunching noise. Images are skewed, when I...

To make things clear, here is another picture. The white box is the Eject Drive Unit, The red oval shows the defective gear, bushing, shaft.
Thanks!25386

Ordered the eject drive unit but it doesn't look like that has the gear, shaft and bushing needed. If you look carefully at the picture in my original post you can see that the defective gear is just...

Finally got it fixed after manually adjusting the laser cams back into the home position and doing the second adjustment that boog suggested.

Thanks for the help!

That's a good point. I did check the gears on the door that would mate to this gear, they looked ok! Is this gear part of the switchback unit?

I'll try this too. Should be on Mon or Tues and I'll let you know how it goes!

So an update!

The customer ordered and installed the fuser himself, but didn't solve the clicking noise. In order to narrow down the problem I removed the bridge unit, definitely coming from the...

Thanks for the post! I will check these things one at a time.


Is there a laser setting that could be causing a color displacement in the main scanning direction? This problem only happened after...

Thanks for all the advice!
I will be returning to this machine later today, I'll take pictures and videos if necessary!

The original complaint was of wavy Magenta background, but after performing all the steps in Canon TP06 07a.pdf the magenta background went away only to be replaced with color displacement during...

Thanks for your advice!

The noise sounds like a clicking noise (from the fuser area) that corresponds with the warm up cycle of the machine. In other words, when the machine is active and making...

I'm having the exact same issue! Were you able to resolve this Communication error?

Customer complains of a noise coming from the body of the machine. It sounds like it's coming from the fusing section. I looked through the manual to see how to engage the motor. The most I can find...

Issue Resolved: Error Code 020-0291

1) Installed new Magenta Dev unit
2) Replaced generic toners with all new OEM (Y,M,C,Bk)
3) Initialized Mag Dev
4) Performed auto gradation