Thanks. I'll try to check that out.
Sent from my Infinix X658E using Tapatalk
Type: Posts; User: Piper
Thanks. I'll try to check that out.
Sent from my Infinix X658E using Tapatalk
I'm having a 341.352 error on my Altalink C8155. What could be the issue? I've not yet secured EDOC for it.
Sent from my Infinix X658E using Tapatalk
Versant 80 Fuser producing rusty dirt from gear assembly. This is making the Fuser belt wicks to get very dirty. How do you stop this? See attached...
Thanks. I will try that.
I've a Xerox 7530 which is not coming on. It only has the power saver light on and 2 displayed on the controller LCD.
The NVM Memory battery is very low at around 0.75volts. Is there anything else...
I have a new Riso RZ 970 colour drum which is giving error code T96-569 even after following setup
procedure ( MACHINE IN TEST MODE 117 START, 890 START, OFF-ON, 887 START ).
It is giving C01-512...
Ensure that the booklet drawer is closing fully and properly meshing with the connector. If that is okay, try replacing the finisher door interlock.
Is it okay to use a vacuum cleaner for suction of Toner drops in the Xerox Colour Machines ( C75, J75, C70, C800 etc )?
Some time back Xerox discouraged the use of vacuum cleaners on some...
Hello All,
Xerox J75 has 041-326 error, which is blown fuse on PWB - PD. I checked the PWB and found Fuse F3 is open (blown).
Are these fuses spared or do I have to replace the whole PWB? See...
Thanks Adrian. It has worked.
I should also say that you are very helpful in this forum. Please keep up the good work.
Hello All
I have a 093-315 error code on a Xerox J75. It was caused by worn out Magenta developer unit gears. What NVM location
can i use to reset the error? On the DC 250 we were using 762-313...
Open the Paper Path Module and check if the Duplex Belt is okay and moving smoothly. If its not moving smoothly,
clean all bearings on the belt path and on the duplex rollers. You will have to...
Check if the Magenta Toner Cartridge motor is rotating. If its faulty or the gears are worn out, the machine
will work for short time and then show that cartridge is empty.
You have to open the...
Have you sorted out the problem? Looks like its the metered supplies problem.
What is the status of the supplies in Supplies status.
Xerox J75 is printing with small ruler like marks on paper edges. This is happening when copying and printing.
How can I get rid of them. Please see attached samples.
Make Sure you have the correct fuser or correct fuser width setting. J75 fusers have a rotary switch with values from 0 to about 8.
When it is set to 0, it supports all media types. So a Job...
Good One!!! But the Xerox Dadf feed roller kit ( 113R00718 ) always comes with the same crappy " sponge " type of retard roller tires. Where can I get a better type of the tires?
Oh! I get your point now. I also do the same but the problem is that new ones just do a few feeds before they start multi feeding.
Anyone with Xerox GSN 11 password generator if its available?
I also have had same issues with these 5600 series dadf rollers. But I cant clearly get your explanation of how to fix it.
Thanks! You are right. The fault code is 116-365
Thanks ACFIFE for your post, but machine is not responding to FORCED HDD FORMAT AND SOFTWARE DOWNLOAD MODE.
When I press those buttons at power up, machine boots up to a 113-365 fault.
I have a Xerox C70 press giving 113-365 fault. Tried pressing 4, stop & Energy Server buttons
at power up to reset HDD but machine didn't respond. Also tried pressing Energy Server button
while...
Spot ON!!! XCOPYTECH. The black plastic under the black DV had toner clots at the bottom and they were touching the IBT belt.
I cleaned the bottom of the plastic properly and prints are okay now.
...
Xerox J75 Press having process direction deletions in the 3 colours ( cyan, magenta, yellow ).
Black prints okay. I have changed IBT belt, IBT belt cleaner, 2nd BTR, Fuser, and colour drums
but...