Thanks Born for your reply. These replacements heads are new and 24 pin the same as what is in the printer. I will take on board your info and next time i go to the customer i will connect my laptop...
Type: Posts; User: gordie
Thanks Born for your reply. These replacements heads are new and 24 pin the same as what is in the printer. I will take on board your info and next time i go to the customer i will connect my laptop...
Hi Can anyone help?
Print head has lines running through text.
Changed print head twice both times they come up with a error alarm and sel light flashing then sel light flashing by itself.
Put the...
Hi Can anyone help? I have a customer with a T830 and a code 0009 0003. I have looked in the service manual and can not find this code.
Regards Gordie
Hi. Remove the right hand cover. The solinoid is in between the two motors about about 2/3rds of the ways up. 2 screws and it comes out.
Regards Gordie
Hi. I don,t know if you have fixed this fault but you will find it is the actuator solinoid sticking, its the rubber perished. you will find it on the main drive unit.
Regards Gordie.
Thanks Synthohol
Hi. Have a c84e that i am looking at, It has on the screen no animation guide available. I believe needs a movie data file installing on the hard drive can any one help with a copy of this file?...
Hi, Can anyone help with a copy of the media file download?
Thanks in advance.
Gordie
Hi I have a Pro-1 with alternating cancel and on buttons can anyone help with this fault? Is there a reset for this fault?
I don't normal do inkjets but this a more expensive printer.
Hope someone...
Hi as far as i am lead to beleive it had a unix program on the hard drive.
Gordie
Thanks for replies, Kiran is right i am lead to believe their is some unix programming on the hard drive. I installed a unix hard drive. The printer booted up to about 20% then asked for usb stick...
Hi. Have a T1300 error code 79.04 customer tried to load latest firmware but would not except it.
By the time a got there the error code is 8.11 checked the lights on the formater and the light...
Hi
I have had several of these printers with this problem and it turned out to be faulty fuser unit.
Regards Gordie,
Hi, Have you found a big increase in the cost of Samsung parts since HP took over?
For example in England.
JB97-01620A ADF Roller Used to cost £1.50 now cost £12.00
JC66-03439A Pickup roller Used...
Hi Thanks for your reply. this is what is confusing me, if I do a component test the paper feed motor works. if you remove the formatter if I am right that removes the firmware a engine test should...
yes I have tried a new toner cartridge. I also connected the new drum motor but did not fix into housing and did a component test and the motor did not work.
Gordie
HP M603error 59.00.30.
Hi. Thiscode indicate a faulty paper feed motor. I have executed a component check and the paper feed motor works ok, the drum motor doesnot turn, the fuser motor does not...
Hi I was originally repairing printer for a sticking carriage but now have a error code 999. Can anybody help with the code or a service manual?:confused:
Regards
Hi. I memory serves me right. It is sim 24.4 TA is maintenance all but you have to execute all of them individually.
Hope this helps!
Hi If I remember correctly it is to do with the earthing or ht to the dev unit. Remove sliver plates on the rear of dev unit give them a good clean with an abrasive pad.
Good luck
Hi I have a Oce cs2136 with a hardware error 03130031/2618 Can anyone help and point me in the right direction as what the fault might be? Do you know the equivalent ie; HP or Ricoh. Your help would...
I allready have a manual
Gordie
Hi Have a hp laserjet 2820 I have been asked to look at. If you print 1 copy it is o/k. If you print anymore than 1 page the printing stops and goes into calibrating then it will print the rest...
Hi I wouldcheck the entrance to the fuser & the guide on the machine just before thefuser as you can get a build up of hard toner.
Hi I agree with The Peanut you need to do a lbp fuser reset. It will not cause any harm! You can also look at the fault & jam history Cannot remember the codes but if you have the manual its in there...