Search:

Thanks. just got these today.

C368 #1
Serial# A7PU012000656
MAC 00:20:6B:A1:91:1C
RESET REQUEST CODE WUJZ8-T5DH9-Y327Q-84VHV-6LJJF-KG8YD-ENBQG-QYDRH

C368 #2
Serial# A7PU012000675
MAC ...

Hi,

Just wanted to see if you would help me with 2 Bizhub C368 I received recently. Tried all usual CE passwords but they don't work.
If you can
C368 #1
serial # A7PU012000675
MAC ...

SWEET! I loaded the firmware and now the code is gone. Thank you so much for the link.

Thank you, I was able to download the files. I am going to format the drive again and install the FW to see if it takes care of the code. Will let you know.

Hi,
Thank you for your help. I have done both physical and logical but cannot seem to clear code unless HDD is uninstalled in SYSTEM 2. I will also need to get the animation - movie file for this...

Hi all,

I have a 654e with a c-d012. I put in a new HDD but understand I need to do firmware to get rid of the code.
I can't find it on the dealer portal, product support, or in the firmware...

I will try this next, already tried a fuser unit. Will let you know - adjusting the TRAILING EDGE REGISTRATION adjustment in service mode does bring it closer but not into full registration.

Hi
Yes did the color registration, skew, and LD adjustments before and after the boards.

Hey all,

Got a bizhub C452 with about 400,000 prints total. Can only see this issue when printing on 11 x 17 paper. Tried scanning but the light gray part of the issue doesn't show up, so here's...

Thanks. Everything went as described in the bulletin except it did not reset the CE password.
Is calling Konica the only way?

Hi.

I got in a used C364 that had some government stickers on it...looks like it had an AU-211P auth unit on it, but I cant even get into service due to CE password being changed from default.
I...

My squeaky idle noises haven't been the fuser, but always the paper exit guide located on the upper part of right door and eject drive section above the fuser (rear side). After cleaning, lubing or...

Start by replacing yellow imaging unit

I see the sample has mixed colors - what do the individual CMYK test prints look like?

Looks like possibly drum ground or something drum related. If you run 11 x 17 does it repeat at same interval as drum? Looked like one sample had 2 cyan patches laid on it that looked about drum...

I had this on a C550 before - replaced the front and back IDCS sensors and fixed my problem - book recommends replacing transfer belt at same time - that's is up to you as mine worked without new...

If all you did was too big a firmware jump, then yes all you need is the main PWB

I have lots of these in the field and have good luck with them...I feel these and the next gen C360-C452 are better than newer models as they still used metal for most of it instead of the newer ones...

question - did you run gradation pattern of each color and did it appear in each color or possibly only one color?
How many copies are on your C353?
Is your eye loop photo of a true black page or a...

I can't tell if skew is from your scan, but it looks like the cyan printed the patches correctly, just ghosted the image a second time on the page. Try replacing the cyan drum unit with another, or...

I will order the new plate and give it a go.
thanks for the info

Thanks for any help on this one.

saw customers transfer belt looked worn and had moved far towards the rear of machine, so ordered a new belt figuring old one was loose and caused it to move....

Hard to diagnose a squeak unless you are there to hear it.
Try swapping fuser.
Otherwise I tend to start removing a gear that drives a particular unit and see if it goes away when that unit loses...

I agree, needs the fixing film sleeve. Takes a good 45 min to an hour to do it properly. ir2200-3300 was similar process, but was so much easier to disassemble fuser.

I suggest looking it over...

Hi,

we have some various accessories including finishers, job separators, attachments kits, etc for these models.

Contact me if interested.

Thank you