The same ritual with "Start + Function clear" button for the other service mode;) and #1048#.
Enjoy..
Type: Posts; User: Toshitec
The same ritual with "Start + Function clear" button for the other service mode;) and #1048#.
Enjoy..
The fault is created by the CCD unit in the DSDF document feeder but can also damage the SYS-board (most common). I had this problem two times with different machines.
Be carefull to replace one at...
Ahum, latest firmware is ,2173 can you imagine??:(
Its not possible, it keeps asking to feed originals in the same target. Switching flatpanel to RADF vice-versa is not possible.
You can try to adjust code 05-3047 with smal steps.
It changes the default position of the carriage when scanning with RADF in color.
Good luck.
Hello, is the 2e transferroller in good shape (fysical) including the contacts?
Maybe current leak because of bad plastic bearing of transferroller?
Good luck
Please check the axels that are responsible for the transport of the Original.
It is possible that they turn too heavy because of the dry bearings.
You can check with the green wheel under the...
For this problem I can say, try to downsize the drive-up time from the LCF.
Start up with 0-5, choose code 457 and take steps of +/- 5 down from the original number.
You can try this until the...
Hello,
On a ES-255 we have a returning EB50 from drawer 2.
I checked the sensors (visualy) and switched the feed-blocks from drawer 1 and 2.
So far no result.
Does anyone have more ideas?...
Hello, maybe it's a problem with the high voltage circuit.
When there is a high voltage leakage, the machine stops his proces at random time.
Check the 2 springs on the transfer-unit that provides...
Maybe poor contacts on the dev.unit.
Try to clean them all or treat them with sandpaper.
Good Luck.
You can try to change the bearing on the mag. roller.
Sometimes it gives to much resistance to create good bias.
And check the contact-springs in the side-cover for the transferunit.
Good luck....
Now you are talking about a serious error, I have also had this on a es-167 and never solved it.
That machine gave a E14 error on second drawer only, really strange.
I have no idea what is going on...
Hello, I think that everybody thinks you have a problem with a Chang Jiang model but you are talking about a Loire model.
Please check te drawer setting of drawer 1, does it correspond with the...
Did you trie to print out the function list in user section ?
I thought there was a counter and a scan total on it.
Good luck.
You can try to change te CF-card in the net-controller (TDK brand)
In the past years I have changed few of them with good result.
Good luck
Hello Michael, thanks again for your reply. Those are just the two things I tried at first. I have used a new doc-feederollerkit and also a new registration sensor in the MR-3019 doc feeder.
Than I...
Hello,
Can someone help me ? I am struggeling with an error in a ES-207.
It keeps jamming with the code E71 (orig. registration not reached in RADF)
Paper gets in and comes out straight and not...
Hey Michaelc, thanks for your reply, the sensors that are reading the reflective strips were dirty. I cleaned them and all color prints are perfect so far.
Thanks again.
Hello, also the same problem here. Greased the 2 bearings of the upper fuser roller with heatresistant oil and now the noise is gone.
I cannot explain the cause of this problem but it was also at...
Hello everybody,
I need your help with a problem on a ES-281C.
Random it puts all cyan on the wrong place on the copy or print.
Quality of print is oke it is just wrong placed. (cyan)
It is...
Hello everybody, I am new on this forum. I have a question about a Toshiba 451C.
It gives a row of random colored spots on leading edge when I print or kopie in full color.
The drum including TBU...