Search:

I am having the exact same issue. Can you confirm if the change of Read Roller fixed your issue please?

I have cleaned and tested read sensor and it is fine, but the paper (if A4 orientation) just...

Thanks very much mate. Much appreciated!

Good evening,
I'm afraid I don't have the parts manual for the MR-3016 on my e-Studio 230.

Could somebody be able to tell me the part number of the part in the picture. It is a long black bar...

Thanks aalex. I have been able to update 0, 5 & 6, but was unable to update the NIC firmware as it failed twice.

The current versions I have installed are :

08-924: v027.0003
08-933: v015.0011...

Yay, I have obtained the correct firmware files and the copier is now back to its old self! Thanks to everybody!

I only updated options 1,2 & 3, (HDD update, UI Data Update, System Firmware...

Follow up:

With the 200GB drive still installed I was about to format the drive by 08-690. (I have done nothing with the firmware)

The copier then booted in to normal operation and I have been...

Thanks Mr Spock, looks like I've sourced the wrong firmware and I don't have an IDE drive small enough.
Thanks for all your help...not sure what I'll do from here!

I'm having some problems if somebody might be able to further assist.

- I replaced HDD with a WD 200GB
- clear + 3 at power on option 3 - completes

- I have formatted a USB drive to FAT (not...

Thanks Mr Spock that is awesome. I do have the Service Handbook, and I could only find the section about 4+9 on power on and do HDD Update, so thank you so much for giving me a great step by step. I...

Good morning,
I've just had an issue with my e-Studio 230, after trying to scan the touch screen became unresponsive, turned the machine off at switch but now it will not go past the boot screen.
...

Well I think I was a bit hasty, the problem still remains.

On observing the RADF, the roller is in its lowered position and will feed through about 10-15 pages successfully. But then it will move...

Just to close and finalise this thread I have fixed the problem.

I don't think this is what you were referring to, but led me to the problem.

What was wrong, was something I must have done when...

Excellent, thanks guys, I will check it out and confirm the fix.

Good afternoon....again,
Thanks to you friendly people, I got a new transfer belt for this machine, and it is printing, however now there is another problem.

I am getting a CA00 or CE40 error....

To finalise this thread, thank you all again.
I obtained a second hand belt that was good quality, installed it, along with a belt blade and the part I broke, and it is now printing again.

(well...

Printing is now looking much better, no more band on the end.
I cleaned (by vacuum) the charger and grid as much as I could, and I also cleaned the grounding wire and bent it slightly to ensure good...

jonezy - Thanks, I will check the firmware and report the version.

canonbundy - Drum and blade just replaced, I will check on the Developer and everything you suggest.

sagar - I just replaced...

I am getting a band at the trailing edge of my prints.
It happens in either A4 or A4R orientation, and it will always be the trailing edge (right side of paper for A4, bottom for A4R).

The...

Ah thought so, I'm just have to pay cash sale price :(
Thanks though.

And where might I be able to buy these? Or are you telling me Toshiba is giving me a huge markup?

I usually have to get my parts direct from Toshiba, so I have to pay what they say. I try to get parts overseas, but they don't always have what I need. And in this case I can't find the belt...

Well Toshiba have quoted me for the transfer belt @ $630 ex GST.

Now I need to decide if it's worth it. Thanks again everyone for your help.

Thanks jonezy999, you are a champ.

In my haste/frustration, I seem to have damaged one of the TBU pressure hooks. Is the 'TBU cleanner pressure hook assembly' available as a separate part, and would you have the part number sagar4?
...

Thanks Jonezy and canonbundy for the info. I just saw the whole part at about $2.5k at precisionroller.com so I thought that is what I was up for. So thank you for letting me know that it can be...