Search:

Type: Posts; User: oeshuron

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    1,195

    Re: PPD2_FIN - MX-M565N w/FN11

    Yes I seen the first thread relating to solenoid. The second thread relates to a different finisher same with the provided solutions. Not saying it's not a sensor though it's intermittent.
  2. Replies
    8
    Views
    1,195

    PPD2_FIN - MX-M565N w/FN11

    Like title states getting PPD2_FIN jams with FN11 on MX-M565N. Outside of checking entrance solenoid on paper pass any other suggestions? No special firmware for MX-M565N and FN11 that I see.
  3. Replies
    10
    Views
    1,247

    Re: MX-FXX2 Handshake Tone

    How will changing baud rate affect whether those beeps are used? Going to take a small fax machine over and see if line/jack/phone system are to blame.
  4. Replies
    10
    Views
    1,247

    Re: MX-FXX2 Handshake Tone

    Except this is the sending machine. There are no beeps proceeding the fax send.
  5. Replies
    10
    Views
    1,247

    Re: MX-FXX2 Handshake Tone

    Normally when sending a fax there are fax beeps proceeding so the receiving fax machine is aware of a fax being sent. These beeps can be heard if you pickup the phone on the receiving end. The...
  6. Replies
    10
    Views
    1,247

    MX-FXX2 Handshake Tone

    When sending fax from MX-M503n w/FXX2 the machine does not give the fax handshake 'beeps'. When you pickup the phone on the receiving end you immediately hear fax broadcast tones. If you don't...
  7. Replies
    7
    Views
    1,001

    Re: MX-FN17 - Marks on back of pages

    Tried different fuser unit as well as different paper and did not resolve the issue.
  8. Replies
    3
    Views
    765

    Re: MX-6500 Power Status Flashing White

    Replaced Sub DC PWB and resolved the issue. Reset system to factory defaults and updated firmware just in case.
  9. Replies
    3
    Views
    765

    Re: MX-6500 Power Status Flashing White

    Had another machine doing something similar that ended up being the low voltage power supply so going to grab that next
  10. Replies
    3
    Views
    765

    MX-6500 Power Status Flashing White

    Mx-6500 status led flashing after customer power cycled.swapped mfp board with working board and still wont come ready. Display status flashes white.
  11. Replies
    7
    Views
    1,001

    Re: MX-FN17 - Marks on back of pages

    See below.



    Marks do not appear until after fuser. Hence the reasoning for trying 3 different finishers. We are thinking of trying different paper.
  12. Replies
    7
    Views
    1,001

    MX-FN17 - Marks on back of pages

    Have two marks on backside of pages which appear to be caused by the bunch rollers in the MX-FN17. Their location never changes when it happens and is in the middle of the page and the majority of...
  13. Replies
    14
    Views
    3,604

    Re: Power Requirements

    Just a large number of calls and service codes. We're requesting a dedicated circuit or a moving of the machine. The area its in is small plus its a breakroom type area.
  14. Replies
    14
    Views
    3,604

    Re: Power Requirements

    Well holy crap. What shall I search to find that 13 page pamphlet?

    Or is that a dealer only (non ccr) item?
  15. Replies
    14
    Views
    3,604

    Re: Power Requirements

    There is an ESP Next Gen PCS 20 Amp on it. There is also a dorm sized refrigerator, fellowes commercial shredder, and coffee maker which are plugged into what a appears to be a double gang box. ...
  16. Replies
    14
    Views
    3,604

    Re: Power Requirements

    Just asking if anyone else had a bulletin or tech tip, similar to the ones available from 2011/2014 for older models, for the newest machines. Better than bothering Sharp with it if there is one...
  17. Replies
    14
    Views
    3,604

    Re: Power Requirements

    I looked in the installation manual and service manual. Can you tell me the page it states dedicated circuit as I might be glossing it over? I understand they should be on one, just looking for...
  18. Replies
    14
    Views
    3,604

    Power Requirements

    Anyone have anything from Sharp stating an MX-5070N should be on its own dedicated circuit?
  19. Replies
    5
    Views
    1,435

    Re: MX-6201n missing yellow on Sim 61-04

    Belt was put on 700u1 frame to swap out during pm and didn't realize it. Good information to know. All is good with frame swap. Thanks again.
  20. Replies
    5
    Views
    1,435

    Re: MX-6201n missing yellow on Sim 61-04

    50-22 Fails. Reset values in 50-10. Still no good.
  21. Replies
    5
    Views
    1,435

    MX-6201n missing yellow on Sim 61-04

    LSU Skew is off ~.5mm (will look into adjusting this). However, 61-04 is devoid of yellow. DV Unit & Drum Unit have been replaced. Thinking about turning LSU screw 5 clicks at a time in either...
  22. Replies
    5
    Views
    2,280

    Re: Reset System Pin/Login

    Thank you! Did exactly this and was able to get in and initialize data! I love this site.
  23. Replies
    5
    Views
    2,280

    Reset System Pin/Login

    Have a customer who recently purchased a new machine through us and is wanting to terminate their lease with a Canon dealer. The dealer is being a real problem in requirements to return the machine. ...
  24. Replies
    1
    Views
    2,411

    MX-7040N C1-01

    C1-01 errors.

    Replaced Process Frame (Drum Assy), Swapped Cleaner Drive Motors, New Main Charge Unit. Just threw C1-01 again. Any ideas?
  25. Replies
    1
    Views
    1,223

    MX-M363N Boot issues.

    Two machines. Both giving message Board Sync Error: PCU. One has IcuM Rom Unusual. Both show PCUM as blank during version check and CPFL rom unusual. Happened on one initially while on site. Would...
Results 1 to 25 of 260
Page 1 of 11 1 2 3 4