Yes I seen the first thread relating to solenoid. The second thread relates to a different finisher same with the provided solutions. Not saying it's not a sensor though it's intermittent.
Type: Posts; User: oeshuron
Yes I seen the first thread relating to solenoid. The second thread relates to a different finisher same with the provided solutions. Not saying it's not a sensor though it's intermittent.
Like title states getting PPD2_FIN jams with FN11 on MX-M565N. Outside of checking entrance solenoid on paper pass any other suggestions? No special firmware for MX-M565N and FN11 that I see.
How will changing baud rate affect whether those beeps are used? Going to take a small fax machine over and see if line/jack/phone system are to blame.
Except this is the sending machine. There are no beeps proceeding the fax send.
Normally when sending a fax there are fax beeps proceeding so the receiving fax machine is aware of a fax being sent. These beeps can be heard if you pickup the phone on the receiving end. The...
When sending fax from MX-M503n w/FXX2 the machine does not give the fax handshake 'beeps'. When you pickup the phone on the receiving end you immediately hear fax broadcast tones. If you don't...
Tried different fuser unit as well as different paper and did not resolve the issue.
Replaced Sub DC PWB and resolved the issue. Reset system to factory defaults and updated firmware just in case.
Had another machine doing something similar that ended up being the low voltage power supply so going to grab that next
Mx-6500 status led flashing after customer power cycled.swapped mfp board with working board and still wont come ready. Display status flashes white.
See below.
Marks do not appear until after fuser. Hence the reasoning for trying 3 different finishers. We are thinking of trying different paper.
Have two marks on backside of pages which appear to be caused by the bunch rollers in the MX-FN17. Their location never changes when it happens and is in the middle of the page and the majority of...
Just a large number of calls and service codes. We're requesting a dedicated circuit or a moving of the machine. The area its in is small plus its a breakroom type area.
Well holy crap. What shall I search to find that 13 page pamphlet?
Or is that a dealer only (non ccr) item?
There is an ESP Next Gen PCS 20 Amp on it. There is also a dorm sized refrigerator, fellowes commercial shredder, and coffee maker which are plugged into what a appears to be a double gang box. ...
Just asking if anyone else had a bulletin or tech tip, similar to the ones available from 2011/2014 for older models, for the newest machines. Better than bothering Sharp with it if there is one...
I looked in the installation manual and service manual. Can you tell me the page it states dedicated circuit as I might be glossing it over? I understand they should be on one, just looking for...
Anyone have anything from Sharp stating an MX-5070N should be on its own dedicated circuit?
Belt was put on 700u1 frame to swap out during pm and didn't realize it. Good information to know. All is good with frame swap. Thanks again.
50-22 Fails. Reset values in 50-10. Still no good.
LSU Skew is off ~.5mm (will look into adjusting this). However, 61-04 is devoid of yellow. DV Unit & Drum Unit have been replaced. Thinking about turning LSU screw 5 clicks at a time in either...
Thank you! Did exactly this and was able to get in and initialize data! I love this site.
Have a customer who recently purchased a new machine through us and is wanting to terminate their lease with a Canon dealer. The dealer is being a real problem in requirements to return the machine. ...
C1-01 errors.
Replaced Process Frame (Drum Assy), Swapped Cleaner Drive Motors, New Main Charge Unit. Just threw C1-01 again. Any ideas?
Two machines. Both giving message Board Sync Error: PCU. One has IcuM Rom Unusual. Both show PCUM as blank during version check and CPFL rom unusual. Happened on one initially while on site. Would...