Search:

Good day,

We have an issue of Error code C-2702 on the model stated above.
We have tried to replace the charging units but error still persists.
We have also tried to replace the HV1, but still...

Also encountered this problem in Production Printers ( C1060/C3070/C4070),
not yet resolved.

Machine model is Accurio Press C4070, and it is newly installed.
Consumables and toners are new ( from KM)

5752057521

Good day,

We have encountered a problem wherein there seems to be very tiny dots on the output paper, it can only be seen under a loupe or magnifier.
The effect on the paper is that...

Good day,

Anyone encountered this code on Accurio press 6120 model?

Check prcb ICP but there is no busted

Appreciate usual response

Regards,
Marlon

Good day guys,
Anyone who have encountered jam code j1572 on this model, it won't reset..
Tried cleaning the sensors and replacing them but no good. Upon checking on the Adu board 2 ICP, there is...

Just an update : we have resolved this issue by copying the data of a working unit and upload this data into this machine and it worked

regards,
marlon29

Hello everyone,

Has anyone encountered this error on Bizhub C1100, error code C-2236, pertaining to IDC shutter abnormality. We have already replaced the IDC unit (lower stay assy on parts...

We have recently tested the conveyance drive board, but still we got the same issue on jam

HI,

Anyone encountered this jam code on the fixing unit, J-3204?
The fuser rollers stops its rotation just after the edge of the paper hits the paper exit sensor(PS61).
So the paper was stocked...

Hi guys,

we have a problem on the model Bizhub 950. It displays the error code C-e002/e006 when making copies. We have replaced the OACB and loaded the firmware but still same problem we got.
...

hello,

we have encountered that problem and we have solved it by alligning the plate closest to it. It seems that the separation roller touches the surface of the guide plate causing it to tear...

hi all,

try adjusting the duty cycle on the software switch

hi guys,

anyone encountered the code sc 50-02 on bizhub 920?

We have replaced already the PRCB but it did not correct the problem...

Upon start up, the machine will have an error code...

hi guys,

anyone had experienced the control panel for the press c8000 going white screen. Upon boot-up, konica logo only then screen will go white eventually...
test control panel but no good......

hi,

try to make system initialize, hope it will work

hi guys,

I have a problem with 1 of our Bizhub 920 in field. The problem is that it only displays "copying in progress". The drum motor rotates for about 5 seconds and stops, same true with the...

The paper comes from tray1&2 only, no PF.
I can shoot the registration on the first page but when I run multiple pages, there is a shift of about 2mm
There is also a skew in the upper portion of...

The model is bizhub 1051... Sorry I didn't mention it in my post a while ago

hi,

try changing the second transfer values for thick 3/4 into -20 and the fusing transport speed to -20 also

hope this will help

marlon

hi guys,

has anyone encountered this problem: front and back registration is not good. The shift of the cutting marks on the back side is almost 3mm when running. I can exactly shoot the 2...

hi,
maybe the setting for the controller is not correct in the system if it has fiery controller. Try setting to "controller 1"

hi,

The warming up is part of the design of the machine for proper performance. If you want to lessen the warm ups, you should at least try to change the fuser temp in the dipsw for main and 2nd...

yes, the scratch is circumferential to drum surface but the scratch is only small one for the first inspection. The scratch is not on the same position, it occurs anywhere on the drum surface.

We...

Good day everyone,

We have a problem with one of our 6500, the drum always get scratch just like being cut by a cutter blade.
Anyone have encountered this one?

We have already changed the...