Search:

Maybe have a look at KM Bulletin 11244 See if it may apply?

I just setup a C550i on a PC417 yesterday by myself. This can be a beast even with 4 techs to lift. No problem with the Sling.

If you ever find yourself needing to setup a Bizhub and don't have enough man power to lift it onto the base unit. here is how to do it

I have used this myself, and it is quite simple to do with...

I have some consumables for older models see attached list.
No reasonable offer refused you pay shipping.



022B - DEVELOPER PRO 920
1


022H - DRUM UNIT PRO 920

I know this is old but with today's shortages we find we have Black drum and can't get color drums. Do you know if these adapters are still available? and where I may purchase them? Thanks

I had this exact issue. The solution is to do a full system clear. Do not back up anything ie: address book or settings, because importing them again after the system clear will recreate the issue....

"Essential Services" means services, by whomsoever rendered, and whether
rendered to the Government or to any other person, the interruption of which
would endanger the life, health or personal...

I know this is an old thread. But in case anyone is still encountering this as I did. Change SW291 set it to 32 and the Faults Error FB0B will now be displayed properly as an ADF Misfeed. If you...

55 Min is pretty good considering the amount of dis-assembly. How much time did the McGuyver take? By the way great pics!

I'm not sure if you solved your problem yet. But the little black fingers that stack the paper ( the manual calls them "The Grippers" ) have a tendency to crack right at the shaft. If one appears to...

That is the connector! We always left the jumper attached to the wire harness but i see it's not there.

Here what I could find in the old solutions:

A jumper connector with a looped wire (p/n...

Plug the connector with the jumper back into the Key Counter connector and all will be well. If I remember it is on the right side of the machine. You should see a rectangular cut out that would be...

They may work they may not. It really is a crap shoot! But you must know this if you have any quality issues any Tech would blame it on the supplies knowing they are not OEM, and maybe even refuse to...

28788Check or change items 32 and 33 make sure 32 is not put on backwards. There were several mods for cracking trays which can cause miss-feeds. Check to see that no wires were nicked or pinched by...

Make sure the Domain Name is left blank. I have seen on this series were if say the domain is copytech.net and the email is someone@copytech.net the machine will try someone@copytech.net.copytech.net...

The soft warnings on that machine are hid behind a yellow question mark in the upper right corner of the control panel. If you don't touch the yellow ! you don't see the message and most people...

Does anyone know where I can find this? Or willing to share it with me I have an older version of this but it does not have all the features shown in the service manual.

Thanks

There are just too many things on that machine that can cause a "Please Wait" message. More info is required.
What have you done so far?
Do the fuser lamps cycle on and off?
Does the finisher...

Wow what a territory! Some how they cover Surrey BC ( Canada ), from Hampshire UK. juliano your company sounds great the job offer made me smile.

Set the default mode to group, then :

1. Touch the Utility button.
2. Select User Setting.
3. Select Copier Setting.
4. Select Sort/Group Auto Change.
5. Select Yes

jr2748 it doesn't sound like anyone was questioning your ability! Obviously you've succeeded in taking the machine appart and putting it back together again, you've read the manual and searched the...

Great discussion guys!
When I previously posted, I was not trying to discourage but rather get anyone considering venturing out on their own to think very hard about what they may be getting into....

I had this problem today, spent an hour on the phone with KM Tech Support remoted in. You need to open "Text Editor" then chose print, in the printer dialog box chose output method, here you will...

If you have a vending product that is designed to work with the KM machine and it is connected to the vendor connection (not Key Counter Plug) I believe it is Vendor 2 mode, that gives you the...

Ok so you say you swapped the devs and the line changed to Magenta. Then swapped lasers and no change. Drums and Charge made no difference. Then I would think the only thing that stayed constant the...