U2-00 usually means a problem with the serial number on the SCN-MFP pwb. Send the 22-06 data to a USB stick using sim 56-05. You can then look to see if the serial number for the SCN-MFP pwb and PCU...
Type: Posts; User: sharptech
U2-00 usually means a problem with the serial number on the SCN-MFP pwb. Send the 22-06 data to a USB stick using sim 56-05. You can then look to see if the serial number for the SCN-MFP pwb and PCU...
The MXM465 has a toner add magnetic clutch. As you did not mention it in your post I would take a look at it. Maybe it is slipping ?
T.G.G.
If you are getting into the world of Pantone I suggest you buy a Pantone color bridge for both coated and uncoated papers. You will need it to prove what a pantone color actually is. Your customers...
Try Sharp`s REP2304 as it explains the process to re align the unit. My suggestion is to replace the unit.
T.G.G.
I would make the lead edge and trail edge voids 1mm larger than what the manual says. Remember the trail edge of the first side becomes the lead edge of the second side when duplexing.
T.G.G.
You stated the FN22 was used. How many sheets of paper have gone throigh the finisher?
T.G.G.
just use a coffee stir stick from MacDonalds. You can get them for free.
T.G.G.
This will occur when 2 thermistors in the fuser that should be sending the same temperature information back to the PCU pwb are not sending the same information. As you have change the fuser already...
If it were me I would let the customer know in writing that bending the prongs on the plug so it can work on a 120v 20A line could be a fire hazard.
Heaven forbid there is a fire. You know the...
What finisher option or receiving tray option do you have installed ?
T.G.G.
On these new models you will have to contact Sharp to get the password reset. Sharp will give you a code that needs to be entered into the machine. No more dip switches.
T.G.G.
Based on the model number this unit is at least 9 years old and probably has a lot of usage on it. Based on this I would take a look at the main drive pack on the rear frame.
T.G.G
Very strange. If you are able to do a shading adjustment then that means that ccd , flat cable must be good. If I remember correctly when the shading adjustment is done the information is stored on...
What is the part number of the shading test chart you used to do the shading adjustment for the ADF ?
T.G.G.
They look like the screws that hold the fuser in...
T.G.G.
I agree with mansart. Every time I have had this same problem changing the 2 magnetic clutches in the LCC has resolved the issue.
T.G.G.
Have you checked to confirm you are getting the 2 voltages to the HDD. If I remember correctly the voltages for the HDD come from the Mother Board and this board failed a lot. I hope you get the...
If you use a PCL drive it will most likely count them all as color. Try using the PS driver and it should count only the color pages as color.
T.G.G.
Those soft switches are for the fax option. They will have no affect on copy/print quality.
T.G.G.
See REP2114
Maybe they mean H5-01. If so then they had 5 jams in a row in the fuser. Check the fuser pawls.
T.G.G.
when you say you have done calibration what simulations did you perform and in what order?
T.G.G.
what about changing motor speeds ( fuser , registration )
Just a thought.
T.G.G.
Have you checked to see if you get a voltage change at the PCU pwb with and without paper in the bypass?
If you get a voltage change the PCU pwb is bad, if not voltage change then maybe the...
To print PDF documents from the USB you must have a the Post Script option installed.
T.G.G.