Hi
I would start with deleting the print drivers and reload them. also try printing from another computer if that dosn`t change anything try updating the firmware and if still doing it then my...
Type: Posts; User: geardriven
Hi
I would start with deleting the print drivers and reload them. also try printing from another computer if that dosn`t change anything try updating the firmware and if still doing it then my...
Hi
Just my 2 cents does the lines appear if you run it through the ADF the same as off the glass I have seen a speck on the optics cause similar problem
HI
I have several hundred of these copier in the field what i find is the shaft that holds the feed tire is bent if you spin the tire you will feel it get tight then loose try swapping the paper...
Hi
I have found that sometimes on this copier the lower fuser frame plastic that holds the fuser bearing from moving side to side breaks and the fuser bearing move out of place causing a load and...
Hi
If the lines are on the back of the paper then its coming off from the transfer roller usually that means the developer is shot.
did you run the developer installation (2-214) when you...
In the waste oil bottle there is a black actuator that floats when the oil level rises. make sure it is sitting down in the waste oil bottle if you emptied
the waste oil bottle the oil may be...
I think you have to replace both units BCU and the IPU so the speed of the machine matches.
:cool:
Sometimes the feed tire bar gets bent if you rotate the feed tire you will feel when it gets tighter just lightly try to straighten the bar out I have had good luck with this it also works when you...
Hi All,
I have a customer that has checks that are security coded, It comes out black when they copy or scan them
I know its a security feature but is there any way around it? I have tried to...
I was afraid of that. does anyone have access to the latest MP C3000 firmware?
Hi Guys,
I have a MP C3000 /4500 that I am having problem with SMB scan with windows 8 i read that it needs new firmware. I am not sure any help would be appreciated.
I use a Utility Knife place a rag down and just run the knife down the roller it takes 2 min and your done
HI all,
I was wondering if you can use a Ricoh MPC3000 drum unit in a MPC2800 I know about shaving the connector on the angle
But do I need to change any wires in the front connector?
I wouldn't think it the reg clutch just because it only does it when he duplexes. I believe there is a duplex exit sensor that might be the culprit.
I agree the registration clutch is slipping causing your image to be off the page. this will cause your jams because the timing is now out of sink.
I Agree I have tried to put try flow on the shaft it seams to work for a while but a few weeks go by and your back to replace it.
the cost of fuel I would replace it.
I agree sometimes the plug stays in the toner hopper I would start by removing the toner hopper and pushing the toner shoot on the PCU (left front side were the toner falls in) look to see if the...
I agree its a high voltage problem I have had a few HV boards cracked causing this code.
Check both cassettes is the slant in both cassettes ? if yes stop the copy before the fuser unit is the slant there? if yes then your reg bushing are worn allowing uneven pressure if no then its in...
i have oiled them before make sure you use very little oil to much and it will code out. remember you can use most small Ricoh poloy motors
1013 ,1515, mp161 220,270 they all will work.
Thanks for the info.
Hi Guys,
I was wondering if anyone knows the part number for the Ricoh 2018 postscript 3 board?
Hi reset the DV counter service mode 7 992 004
I have at least 400 of these machine in the field still and 90% of the time the t/s coronas are bad. take the t/s unit out of the machine make a copy stop it under the drum. is there a image on the...
Hi
I rebuild these all the time type 18 or 19 will work I would replace the gears, clean the charge roller
and apply a thin coat of ne finish polish this will help stop the thin lines from coming...