Here is some more info/history. This machine was purchased from another vendor 7 years ago. It had a firmware update about 4 years ago by internal IT person at the account ( he used his source )I was...
Type: Posts; User: Discountcopiers
Here is some more info/history. This machine was purchased from another vendor 7 years ago. It had a firmware update about 4 years ago by internal IT person at the account ( he used his source )I was...
i ordered another (used) mfp pwb , i tried re=seating all dimm and e-proms rom chips. and sim 14 thru 24... we will let you know by next week
Ive had a sharp at a location for 5 years or so and they called with a A0-20 code Will not reset through sim 24 any any of the normal ways . unfortunately i did not back up the firmware upgrade two...
I have a subcontractor that is having a problem with image shifting .
Here are the syptoms.Shifts on all trays ,on the glass,document feeder and print mode.
it definetly is a processor problem.
...
THESE SOLENOIDS AND ONE WAY CLUTCH ASSEMBLYS ARE VERY SENSITVE TO DIRT AND DEVELOPER. GREASING (WHITE GREASE) WOULD BE PART TWO.. FIRST CLEAN THE ONE WAY CLUTCH SPRING AND SHAFT WITH wd -40 THEN...
Are you a tech? Does it have any skew or is it a non-trapazoid shift? Is it in the direction of scan? Does it do it on print mode? If you answered the first question no ,di-regard the rest.
THE MAGNETIC ANGLE ON THE MAIN MAG-ROLL MAY HAVE SHIFTED. IF YO HAVE SEVERAL CONTRACT CUSTOMERS TRY SWAPING DEV UNIT TO9 SEE IF THE PROBLEM FOLLOWS THE UNIT. i KNOW ALL OF YOU ARE SHAKING YOUR HEAD...
may be time to upgrade . I have had many calls for sofware conflicts with older konica s using windows 7-8. My sales person knows about this head
each!
I went out on a new call for blurry copies .. seems typical call...Wrong. 1.4-1.6 pts it starts to look washed outit looked as thou the drum had water contamination.solids are black with no...
if the other two fixes dont work... try open front door.. cheat the sensor to close use a spring hook to manually move the reset sensor one second after you cheat the from door.
I agree...... you should use an oem cartridge only or fully reman. I have had some issues with the refills. the drum and blade cost about the same as a good reman.
kyocera km 4530.It has a an intermitent problem with jams . I narrowed it down to the drive area of the fuser and transport module. I check all the gears for binding. I manually moved the drive...
just to let everyone know... it was the cracked gear that caused the distorted color shifting.it was cracked on the inside pin coupling side. looked great on the outboard side. thanx again for all...
I have kicked myself many times for the same reason... I ordered the gear and some related parts. ill be back there on tuesday.
I know which one you are talking about.I thought i had replaced one that came with the primary trans kit.?? ill be back ther on thurs to check the problem. thanx for your help.
thanx...You are refering to the gear on the inboard portion of the machine? or on the other side (back) ? or on the primary transfer assembly itself . it seemed to have more play than before. I was...
I am working on a mx7001n with about 350k on it all the mntc is up to date. at about 250k it intermitently started shifting registration toward the lead edge. I did a registration adjustement to the...
I am working on a mx7001n with about 350k on it all the mntc is up to date. at about 250k it intermitently started shifting registration toward the lead edge. I did a registration adjustement to the...
I am working on a sharp arm450n the low voltage power supply has gone bad. I have a power supply for a arm455 . it looks very similiar, with the exception that of a few connectors. I did try it and...
the only problem is that my backyard is full of old canons and xerox's , otherwise i'd bury it for him, after a couple of kicks for old time sake. the toshiba's do the same one little crumble and its...
yeah... it went into "download mode" which throws my theory down the %&$#er. Any suggestions ?, my nest idea is to find a hole big enough for this beast! the customer has over 4 mil and wont upgrade....
ther are a couple of ways to fix this. you can buy some LOC-TITE and use a screw with more Girth and let it dry overnight before usage, or you can buy LiquidNails and this dries in about an hour ....
ill give it a shot. ...but,do you have an used panel or pwb I can buy off you? just in case of wasting time of removing it and customer fustration on waiting for it to be operable. i can pay thru...
I need a second opinion on this machine problem. I cannot get into diagnostic routine which is (additional func)* 28 *(addtional func) to clear a fuser fault.( E0000-00003) I checked all the...
my vendor Triple sss rubber went out of business.