I have this KM 1650 that gives me copies with faint patches but when you do print outs, the printouts are perfect!
I have cleaned the optics and infact, I even replaced the scanning lamp and the...
Type: Posts; User: same_steven
I have this KM 1650 that gives me copies with faint patches but when you do print outs, the printouts are perfect!
I have cleaned the optics and infact, I even replaced the scanning lamp and the...
Hie,
I have this Konica that gives the above error, I have tried changing the registration sensor but the error is persistent. What could be the issue?
Thanks
Rgds.
Thankyou Black cat...the top cover had issues as the rear post was broken. I got that fixed and the machine is happy and running. I really appreciated your help.
Hie guys,
I have a Km 4050 that I recently installed a DP-700 document feeder.
The funny thing is when you put papers on the DP, there is a massage on the touch panel "Please wait, adjusting...
I have a km 4050 that won't boot.
The initial problem was with the power board, I found a lizard had shot the board.
I had it repaired but it didn't work so I ordered another one.
On puting the...
Hello comrades,
I have a KM2050 with a metre reading of 318,914. When you are copying or printing, the first few copies will come out nicely but then after ten to twenty copies/printouts, it will...
Hey friends,I have km4050 that is the centre of all problems.Firstly,when you switch it on,it may power on or just give you a blank screen(with the power led on).Secondly it keeps giving this error...
Guys, nothing seems to work...I upgraded the firmware using a usb drive since I didn't have a CF card. Is there a difference? The machine still doesn't enter simulation mode. Would changing the...
CFB31c fixed but still the machine wouldn't enter setup mode with 10871087. Is there any other way of clearing the error (c6000)?
Thankyou very much but I cant run u163 because the machine doesnt respond to 10871087
Dear friends,
I have a KM-4050 machine with the above error...the machine does not go into service mode when I press 10871087. Immediately i switch on the machine the error pops up and it doesn't...
Dear frds,
I have an est 167 that when you switch on it has nothing displayed on the screen just the backlight and after a few minutes it goes off.
On pressing *, 1, 3 combination it displays...
dear harnack, Can I get firmware for IR3180c? ngure.jackson@gmail.com
Hie frds,
I am not familiar with the epson machine kindly help with the above error.
Thanks and regards,
Same steven
To be honest I am not very familiar with this kind of machine. I don't know how to test the sensors in I/O mode. The machine works fine on one sided copy but on duplex the paper crumples and when you...
The reason I am asking this is because i tried changing the cluthes in the duplex unit but the problem still persists. Anyway thanks so much buddy you are the best
Is it just the sensors or even the clutches?
Hey guyz,
I have this error that is giving me headache. How do I go about it please?
Regards,
Thank you so much guys but how do you get to the simulation mode?
Dear Friends,
I want to thank this community for the support it has encouraged among technicians.
I have a Kyocera Mita 1500 with the error c6400.
How do I clear it?
Your help will be highly...
Hie frds,
I have an Est 230 that is displaying error E030 that just refuses to go away.
I have checked everywhere there is no paper jam.
I have cleaned the registration sensor and serviced the...
Hallo guys,
I have an Est 166 that is giving blank copies when copies are done using the ADF.
When you do copies on the glass platten, it gives a very wide margin at the top and some text...
Good people,
I Have an Est 181 which am trying to instal on windows vista using usb connection.
after installing when am trying to print it gives the error "c2 driver error, low level error...
thanks my guy i was able to clear in service mode.
Hie frds,
I have the error mentioned above, kindly assist.