Search:

Type: Posts; User: chubblies

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    425

    Re: microsoft print connector MX2630

    Do you mean WSD? If so, ditch it and use tcp/ip instead. WSD is utter rubbish. Are you using the correct driver for the 2630?
  2. Replies
    4
    Views
    542

    Re: Lexsharp motherboard swap

    3 year parts warranty with Lexmark so would probably be free if it was native Lexmark:p

    I would think it would work as you restore the serial etc using the service restore tool once done, and I am...
  3. Replies
    6
    Views
    1,221

    Re: Sharp MX-4070V

    Dropbox - 3570.imgc - Simplify your life
  4. Replies
    4
    Views
    587

    [Electrical] Re: Sharp MX-6240N Power supply Board

    Sharp do not provide actual board circuits anymore, they only provide block schematics.
    There are a few soldered fuses (genius Sharp, irreplaceable fuses) on both the AC and DC psu's, I would start...
  5. Replies
    2
    Views
    1,170

    Re: xerox d95 prints smudged

    Did you run through the developer setup once replaced? MAX setup?
  6. Replies
    5
    Views
    1,182

    Re: Versant 180 drum life

    It doesn't stop the machine at 0% though does it? It thought it just ran over and on, but just displayed the message?
  7. Replies
    10
    Views
    1,696

    Re: MX-2651 messed up colors/black

    What about on the drums? Are the transfer belt positions correct when it switches the cams down?
  8. Replies
    10
    Views
    1,696

    Re: MX-2651 messed up colors/black

    Is there a whole width image on the transfer belt? It looks either 2nd transfer not pulling the image or laser shutter partially blocking laser.
    This needs proper diagnosing before throwing loads of...
  9. Replies
    4
    Views
    1,013

    Re: Versant 80 Fiery P2X

    Why are you reloading? If it comes up 00 it should be fully working. You can reload via ethernet also, you just flip one of the dip switches and it issues an ip to your laptop to connect.
  10. Replies
    2
    Views
    846

    Re: Developer material differences

    I fitted 7655 toner to a Versant by swapping chips to avoid wasting the old 7655 toner along with dev on lots of older Xerox's (C7545 up to C8070 for example) and it works fine. Most dev is the same...
  11. Replies
    5
    Views
    1,495

    Re: altalink c8045 too much yellow

    Did you enter the TD sensor ID setting into diagnostics? and set up the dev correctly? You must do this or it over/under tones the dev.
  12. Replies
    30
    Views
    6,810

    Re: Co Inquiry about sharp series 4

    I remember the toaster. Fire extinguisher always close by to the machine in case of excessive fuser jams :)
  13. Re: What has been your experience with new Epson ink pack machines?

    We used to work on them and they were utter shite. We had the RIPS 5790 from memory. Difficult to work on and printheads failed like no tomorrow. Terrible things, and we were glad to get shot of...
  14. Replies
    28
    Views
    5,366

    Re: L4-19 MX-6071

    We have had the same on high volume machines. We actually took apart a waste box where it had happened and there was loads on toner in one compartment that had caused the pcu unit to snap auger, but...
  15. Re: Canon imagerunner adv DX C5840i, no cyan color

    Basics needed here. Check developer for coverage, wrap charge roller with tape to block charge in that area to see if you get a solid band, stop mid run and see if there is a image on transfer belt,...
  16. Replies
    3
    Views
    668

    Re: Xerox j75 fuser temp

    Are you setting the media to the heaviest setting possible?
    There is a heavy duty media fuser available for these machines, you probably need one of those. Hotter temp will only blow the thermal...
  17. Replies
    3
    Views
    418

    Re: Sharp MX-M850 Not Switching On

    Are you using both power cords? And is the main switch inside front cover on? You need to meter up the various sections to see where power is getting too, but if you don't know what you are doing,...
  18. Replies
    8
    Views
    1,158

    Re: MX-C357F noise when printing double sided

    1 year parts and labour warranty and 4 years parts warranty with the Lexmark version too INCLUDING fuser, imaging kits:o
  19. Replies
    11
    Views
    1,737

    [Jamming] Re: SHARP MX 3051 - Paper stick on the roller

    56872
  20. Re: Sharp MX 3110 N Power indicator shows yellow and will not power up.

    Are you using pcl driver? Machine doesn't come with PS out of the box, but I am not sure how it presents itself if you send a PS job to a non-PS capable machine.
    Worth retrying the SD card cloning...
  21. Replies
    30
    Views
    12,696

    [Misc] Re: Xerox Altalink C80xx Altboot fail, boot loop

    When you 1st turn it on, it boots from the SD card. The display you see created on the screen is all from SD, and it then boots from HDD/SD to bring the machine fully up. The fact it says B8045...
  22. Replies
    8
    Views
    899

    Re: Sharp MX2640 - Please wait

    100% SD card. Use HDD raw copy and create a new one directly onto a new SD with a known working image
  23. Replies
    10
    Views
    967

    Re: drum counters MX6070V

    This is an MX5070, same fw as a MX6070 so I cannot see how it does not show. Weird.
    54832
  24. Replies
    10
    Views
    967

    Re: drum counters MX6070V

    Scroll to page 4 of the counters I think, it certainly shows it in 22-13
  25. [Electrical] Re: Xerox workcentre 7225 slow UI found a resister on the mainboard any know what it

    That's pretty normal speed for Xerox. They are dog shit slow
Results 1 to 25 of 148
Page 1 of 6 1 2 3 4