all the parts I replaced was by Sharp recommendation .And once again they haven't come thru with a answer.thanks for the info
Type: Posts; User: rainmaker
all the parts I replaced was by Sharp recommendation .And once again they haven't come thru with a answer.thanks for the info
Thanks for the info.It doesn't have a fax on it.When the machine is not used and goes into power save mode.i guess I should have said.When they send a job it drops off the network but not all the...
have a Sharp 4101 that when it comes out of sleep mode the key board doesn't respond.you have to turn it off then back on .it also drops off the network.I have replaced the mfp board the sd card...
Have a odd problem with a mx503n.The log report shows TRAY1 jams.Ihave installed a new paper feed unit as well as the paper feed drive unit.I have disable tray 1 and let them tray2 as the main tray.I...
yes sorry it was the msata ssd
the sd card.i believe that was it
have a Sharp MX5070 that while idle will go into a jam.The jam code is FIN_ERR.which as sharp says it is a communication jam.I have replaced the Finisher board and the PCU and did firmware.You can...
Had the same issue with just one of my C1070.I just replace lower roller and bearings.Havent had the problem since.Think it might be a bearing problem locking up.
I would swap the drum with another drum doesn't matter they are the same if you get the same error.then I would do the laser skew and drum phase adj. good luck.The adj is in the service manual adj.6...
did you do toner revert?I would swap the k dv unit with the yellow dv unit.Put tape over the dv slot where the toner goes in.and run it again .see if the error code changes.if it does you have a bad...
I assume that you have done dv replacement before and did toner density sensor adj after dv charge.I would try dv revert on the k dv unit .If that doesn't work either replace the dv sensor or the...
thanks blackcat...might have to open a ticket with Sharp...and.,...well....the other company I worked for they took toner out before shipping it out....
thanks foryour imput.The machine is a doctor/cancer place and they are using it like carzy.have a hard time doing tc on the machine with rec faxs and printing.did notice the waste toner was some what...
have two MXM-753.One the waste toner is filling up and causing the waste gears to sound like a machine gun.The process unit has been replaced and vacuum out the process unit.I replace the dv and cal...
you can disable the tray by going into system setting go to paper tray setting and un ck copy.fax.first I would do test command 15.if this does work you can swap out tray 1 paper lift with tray...
make sure you turn the copier off thru the on/off button and then install the fuser unit,goodluck
on the transport unit there is a drive gear,i have seen the inside of the gear get worn out ,it does have a pin in the center. good luck
Had this code.I replaced the main drive unit,there is a toner waste detect sensor in the unit.Didnt have the clicking noise,I pulled the process unit out and the gears were smooth.Replaced the main...
just checking here to help you out.So you replaced the LSU part#DUNT-8109FCZZ,the PCU part # CPWBX1838FC32,ans the LSU mother PWB part #CPWBX1837DS51?
Did it happen on its own? The error code.The...
noticed in the service manual that the LSU mother board could cause it as well as the pcu and lsu you already replaced.So i take it as soon as you power on it goes into the error?
Got a problem I haven't find the solution.First I do have the service manual and have access to Konica.The problem only happens when I staple,more than one set.It jams as the second set come to the...
picture of copies would be nice.copy count on drums and dv?
have a customer that is using pre-printed forms.there are lines that are blank on the form.when they print IE name ,address,etc.some of the prints do not fall on the line.some prints the name etc are...
working on a kyocera 3900.the problem is that the customer is using a form(preprinted) that when printing to the form the image ie name, customer number,address,etc doesnt line up all the time,some...
try update the firmware .hope this does it for you.saw it on idnc.