Search:

Type: Posts; User: linuxxpwin

Page 1 of 9 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    572

    Re: Canon 2535i Service MAnual

    just purchased Manual Never Mind. All.


    Linuxxpwin
  2. Replies
    1
    Views
    572

    Canon 2535i Service MAnual

    Hi All,


    I have just received a Canon 2535i Copier and need the installation procedure for stirring toner into hopper or developing unit.

    I would be quite grateful.

    If anyone can assist me...
  3. Replies
    6
    Views
    926

    Re: XEROX 8830 wide format

    Hi, you may have a problem with the sensor not sending messages to the cutter to activate and cut paper.

    It appears that you may have a bad sensor or damaged sensor.

    Check to make sure the...
  4. Replies
    0
    Views
    347

    Workcentre 73XX

    Hi all,

    I have been placed to maintain a Xerox Workcentre 73XX model machine with fax feature, however on turning it on I notice a blank LCD.

    I can hear the fans running, the scanning lamp...
  5. Replies
    7
    Views
    937

    Re: Magicolor 2590MF

    yes i did, I even tested outside of machine it just does not get energize, after modifying with a Canon replacement, it worked then.

    I am indeed grateful for all the information given.
    ...
  6. Replies
    7
    Views
    937

    Re: Magicolor 2590MF

    Ok, Thanks to all the help, I was able to resolve issue had a bad solenoid, modified it with a Canon as parts are not available here, and got everything working, will be placing order for correct...
  7. Replies
    7
    Views
    937

    Re: Magicolor 2590MF

    Thanks guys, I did clean the solenoid of the rubber stuff and replace it, but I found that the solenoid is not firing, will try another later tonight, however I may need to modify as I do not have...
  8. Replies
    7
    Views
    937

    Magicolor 2590MF

    Good day all, I have here a Konica Minolta Magicolor 2590MF, where the image transferred to the paper begins at least 3 inches down and while exiting fixing assembly creates a paper jam.

    I have...
  9. Re: Ricoh copier tech needed full time and asap in vancouver bc

    I am interested, very much interested my email address is csjrobertson@gmail.com

    Thank yo9u very much.
  10. Thread: CLC1140

    by linuxxpwin
    Replies
    0
    Views
    328

    CLC1140

    Hi all, Today I receive the shock of my life someone here call me to service a clc1140, ouch, anyways I was able to fix the issue, but I think I should apply here for the service and repair manual.
    ...
  11. Thread: Port 21

    by linuxxpwin
    Replies
    22
    Views
    3,129

    Re: Port 21

    ok, does your network carries a firewall router, in which your entire network connect through? including your network copier/printers. rule exception and tightening is done mostly at those locations,...
  12. Replies
    31
    Views
    2,397

    Re: SP8100 - Hanging on print command

    I was rereading my post earlier and realize I made an error in typing, I noted that the problem is definitely caused by the fuser unit, what is omitted is not this would not be a cause of the problem...
  13. Thread: IRC5030

    by linuxxpwin
    Replies
    0
    Views
    422

    IRC5030

    Hi All,

    I am in need of the IR advance C5030 Parts Manual and System Software.

    Please email me or PM me.

    I would be grateful for all the help.

    linuxxpwin@gmail.com
  14. Thread: Port 21

    by linuxxpwin
    Replies
    22
    Views
    3,129

    Re: Port 21

    As an IT Professional I have to agree with my colleagues above about the port settings, using a different port will not solve the problem as the initial problem is still there and would now allow any...
  15. Replies
    31
    Views
    2,397

    Re: SP8100 - Hanging on print command

    Hi the problem you are experiencing is definitely caused by the fuser unit, I think the problem is an obvious, in a previous post you mentioned you are printing with no output, are you saying paper...
  16. Replies
    31
    Views
    2,397

    Re: SP8100 - Hanging on print command

    ok, this narrows it down, there are a few other things you can check,

    1. Have the memory check change out or increase and test.
    2. Formatter PCB can also cause this issue
    3. DC PCB if you have...
  17. Replies
    31
    Views
    2,397

    Re: SP8100 - Hanging on print command

    ok does the ccd unit init, when copy is pressed?

    linuxxpwin.
  18. Replies
    31
    Views
    2,397

    Re: SP8100 - Hanging on print command

    Have you tried reloading the drivers, or checking for an updated driver or drivers?


    Linuxxpwin
  19. Thread: Port 21

    by linuxxpwin
    Replies
    22
    Views
    3,129

    Re: Port 21

    ports are assigned to certain things with a piece of hardware: port 21 is assigned to FTP
    port 25 is assigned to SMTP (Mail)
    pop3 on 110 (mail)

    and so on, what you can try is to give specific...
  20. Re: UK - Sharp Workshop Based Engineer - Reading/Berks/Bucks

    I would love to apply for this position, would you consider someone from an overseas British territory?

    If so I would like to submit my application with experiences.

    Please me an e-mail...
  21. Replies
    4
    Views
    898

    Re: service manuals

    I have checked out the site very good info but I am not seeing the models I posted for support manuals, can you please direct me which of these?

    Linuxxpwin
  22. Replies
    4
    Views
    898

    Re: service manuals

    thanks a bunch I do appreciate this.

    Thanks again.

    Linuxxpwin
  23. Replies
    4
    Views
    898

    service manuals

    Good Day all I am in need of the following service manuals and PC manual

    I would be please if you can email me

    linuxxpwin@gmail.com


    IR3230
    IR2530
    IRC5030
  24. Replies
    3
    Views
    811

    Re: IR2270 rdf misreads paper size

    I agree with vigour, however before you change VR, please check your paper size sensing sensors, as I have had that problem before, a sensor was bad and another with the sensor flag broken and...
  25. Thread: Xante CL30

    by linuxxpwin
    Replies
    0
    Views
    641

    Xante CL30

    Good Day all,

    I am in need of the Xante CL30 repair manual and Parts Catalogue.


    If anyone can assist me, please email me csjrobertson@gmail.com

    Thanks in advance.
Results 1 to 25 of 219
Page 1 of 9 1 2 3 4