got one, please disregard
Type: Posts; User: Counsel
got one, please disregard
Hi all,
I have been out of the service officially but still do some repairs for a few friends but I dont have access to ricoh rfg anymore. I am looking for an spc820dn series parts manual. any...
I would hope before replacing all that stuff you checked the flag for the paper end sensor on the feed unit, if a tray is reading empty the flag is probably out of position. If your getting a cover...
Could be a picker catching paper the 5 tooth looking things you can see when you flap the gate open. It could be the tension arms, one presumably the rear side is not closing when you shut the door...
The manual doesnt show the part very well the second feed guide is different then the first one because of that tab, the mylar is already attached to the guide plate. I dont remember there being a...
I have a customer saying when they get a fax the machine recieves it but it can take upwards of an hour for it print out of the machine, anyone seen that before this is a new model to me but an hour...
With the Dev unit out tilt it forward towards the magnetic rollers just a bit and rotate the rollers, does developer cover the entire magnetic rollers? if developer is missing in spots the doctor...
There is a post for this on the same model. Same suggestions as in here with the advice to clean the LD unit and do the laser pitch adjustment procedure. Suggested by TeeBee1234.
35256
I...
35255Here is a image of the guide i circled the spot where you can see there is a post that sticks up and triggers the switch if thats missing it wont hit the switch when the door is closed.
Pretty sure the sub hoppers use a plastic coil to auger and work like the old LP143 printers if it gets clogged and binds it destroys that plastic coil and wont feed toner, your hopper is most likely...
The one i want to replace is the belt at the very end of the dev unit there is a white gear on top and a greyish drive gear on bottom with a copper idler i guess you would call it its just a copper...
I dont do a lot of sharp repairs but i have a mx3500N call and its clicking a lot, seems to be the the small drive belt on the rear of the developer units is slipping around the gears. So i used the...
the transport guide cover on most of those has an arm that sticks up and pushes the switch when the door is closed, if you close the guide flap you should see the arm hit the sensor push button if...
I have had these do that when the main green power button on the panel is not turned off first before shutting off the red switch, when they boot up the panel wont have a display but machine is on,...
I had a church once that didnt have internet at all and they would walk across the room and connect a usb and stand there just to print with their laptop to make it easy on them I gave them my old...
So this did end up being a bad assembly right out of the box once it was swapped with a new one it ran fine. Thats the first one i have had not work out of the box
I actually had this yesterday with magenta it would load the toner and said it was empty, so i just tried a second new bottle and it loaded fine, i chalked it up to bad rfid chip and sent the bottle...
In case this happens to anyone else it ended being the BCU
ya the rom was up to date on the new nvram, but as always i reloaded it all just in case and it didnt make any difference. I did reformat the hdd but used the sp mode to do it so who knows, i going...
i would recommend what slimslob mentioned. That suction motor for the toner dust is replaced at so many hours when the meter goes a lot guys like to just reset the hour meter and leave the pump...
Hey all,
Having a bit of an issue i have not seen before on a mpc2051, this machine got new nvram a month ago due to failure to update rom and stuck in a can't update but need to install sd card. ...
Internal finisher? Side mounted? The side finsher will have a bridge unit which can have faulty push switches or dirty sensors. The internal one could be several other things. The jam code would...
Well if it works fine in tray 2 position it must be ok tray wise, i know that spring clutch is a pain for tray 1, #2 is easier to get at but of course 1 usually fails first. That spring clutch would...
With 300k pages have you tried replacing the tray feed roller and sep pad? The majority of my non feeds on those machines were the guide on your left hand side when you open the tray it should be...
I think I will try a new one and send this one back to the boss for warranty credit