Search:

I have tried a whole panel still didn't work, so far I have replaced the BICU twice, the mirror motor twice, a full laser unit, the op panel, PSU, high voltage. There are lights flashing on...

no response and no cycle on start up, it doesn't even attempt to boot no motors running no sound no nothing just the green light on power button

cannot even ping it even though there are lights...

the machine has power there is green light on power button on op panel and i have replaced power supply and high voltage still no good

As the title suggested have any of you guys come across this problem where the mirror motor and BICU did not fix a dead display screen. (screen is blank cant see anything even if you shine a torch)
...

Hi guys

Thanks for all the input and a big thankyou to imaginemoko, the issue has been resolved it turned out to be paper setting mismatch from the bypass. Feels like a monkey has just been...

Now that you mentioned it I do remember the client saying something about the bypass, I will go and check the bypass settings tomorrow.

will try that and see how it goes

I have not tried a different power outlet as there is a shredder plugged next to where the machine is plugged in and it is working fine but that is something I can try. The timing of the codes seems...

yes still no good

yes I have tried that as well error comes back

Hello everyone

I've got a machine that keeps coming up with sc543, I have tried 2 new fusers (thinking the first one was faulty), a PSU and a AC controller board also firmware is up to date. I...

Just a FYI, co$tly exercise unfortunately.... We should have had the previous service agent do the work before we cancelled the service agreement...

Thanks for the heads up.... Sounds like I'm going to have to get an agent to come and do the HDD format and firmware reinstall to keep the machine operational after the HDD format.

Hi All,

Our Toshiba has reached its End of Lease period and we are getting rid of the device. I am wanting to know how to do a factory reset of an e-Studio 2820C so that all that is listed below...

Thanks qbert69 for the reply..

Unfortunately it isnt a seperator page as the blank page that comes out is meant to be the 1st page of print. ie, 3 page document but only the last two pages with...

Hi All,

We've got a few Xerox M455 MFPs as well as some larger Xerox A3 MFDs which we are using in a Citrix environment. Printers are hosted on dedicated print servers. Printing documents (such as...

We have had this issue occur on nearly all our Mpc 2050 through to Mpc 2551 range. Did most of the above mentioned and has never fixed issue. Through frustration, i decided to advise the client to...

Hi

I have a Lexmark X656DE that when you switch on the screen will stay blank/black and it will beep 3 times then stop then beep 3 times again then stop and it will continue the sequence of...

Teebee, dont know how long you have been doing this but you are good!! Are you technical support cause i have seen some of your replies and you are always on the money and you have also helped me in...

We have this prob all the time. The problem is the fuser cannot handle anything with a full colour leading edge. You will also find that it will wrap around the orange roller if your paper is moist...

im getting sc 400, 401,402, 403, 405 intermittently. Have pulled out transfer unit and cleaned up as initially thought toner dropping down from pcdus were the cause but came back 2 weeks later. Drums...

From what i have seen in machs in this series in which have done high volume and dev tanks leak firstly it is a result of stretching developers and also could be dev tank fatigue. The main dev tank...

tcs04, Thanks for your suggestion. Yes the AF 1060 series to MP8000 are almost identical still accept for some boards obviously. I like the sound of your suggestion as i got to the point where i...

Im 100% sure my controller board was working. I know this because i actually swapped it out of a working mach. I then got the controller board from the faulty mach and put it in my good mach and my...

Yes i unplugged the HD harness from the controller side and it still done the same. I am looking as point to point diagrams now and am hopeful that i will find a soloution. Thanks for your suggestions