Search:

Type: Posts; User: Laserbeam

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. [Misc] Re: C454 - Paper comes out curly (approximately from the half)

    Problem solved!!!
    The cause was in the reversal unit. Unfortunately, an error encured during my first error Analysis. I had a reversal unit installed from a BH C224.
    However, this unit has a...
  2. [Misc] Re: C454 - Paper comes out curly (approximately from the half)

    @ Gaffers01

    yes, I had already made this attempt. As soon as the paper become visible, I pulled it out under strong tension.
    But the paper is still curled. Thus, the possibility that the paper...
  3. [Misc] Re: C454 - Paper comes out curly (approximately from the half)

    Now I've changed following components:

    vertical Transport assy (which includes the paper loop sensor above the transfer roller)
    both registration rollers and bearings
    registration actuator
    CL6...
  4. [Misc] Re: C454 - Paper comes out curly (approximately from the half)

    okay, this attempt I will do tomorrow!
  5. [Misc] Re: C454 - Paper comes out curly (approximately from the half)

    @ emujo2
    I have just installed a new tranfer roller, unfortunately still the old problem!

    @ blackcat4866
    I replaced the whole Fixing drive assy! In this assy there is a new CL8. no jam 30-03...
  6. [Misc] Re: C454 - Paper comes out curly (approximately from the half)

    that's what I`ve tried with A3.
    The location where the problem occurs is between fixing unit and paper exit unit. Between registration roller and etrance fixing unit the paper is not curled!
  7. [Misc] Re: C454 - Paper comes out curly (approximately from the half)

    @ Phil. B.

    the paper can be excludet! I have tested several qualities, the problem still exists.

    @tsbservice,

    yes, on the picture in the attachment, it`s A3-paper. That`s the best way to see...
  8. [Misc] C454 - Paper comes out curly (approximately from the half)

    Hello,

    I am so desparate!

    A bizhub C454e (total Count around 1,5 Million) shows the following problem: The paper shows about halfway a wave-line shape.

    I habe already changed the following...
  9. [Jamming] Re: bizhub C458 from Tray 2 Jam-code 12-01 (feed roller didnīt rotate)

    @ tsbservice,

    yes, the one-way gear was the problem! It was seized on the shaft. I renewed the gear and the shaft and now everything works fine.

    Thanks for your tip!
  10. [Jamming] Re: bizhub C458 from Tray 2 Jam-code 12-01 (feed roller didnīt rotate)

    Hi tech51,

    many thanks for your fast reply! Can you tell me more? What do I have to exchange? Do you mean the Paper Feed Drive Assy (PN A79JR70222) ?
  11. [Jamming] bizhub C458 from Tray 2 Jam-code 12-01 (feed roller didnīt rotate)

    Hello,

    a bizhub C458 basically shows jam-Code 12-01 only from tray 2. Tray 1 is working fine.
    If I remove tray 1 and watch the two feed rollers of tray 2, I notice that these didnīt rotate, a...
  12. [Misc] Re: bizhub C3351 with strange noises (only in color-mode)

    The problem is solved!
    TB Drive Frame Assy (PN A92ER70200) was not properly mounted in the factory!
    The positioning pins were not properly in their holes and this caused the assembly to warp.
    This...
  13. [Misc] bizhub C3351 with strange noises (only in color-mode)

    Hello,

    a bizhub C3351 makes strange noises, only in color mode. In black and white mode, these sounds didn't occur.
    I habe already changed following components:

    Transfer belt, Fixing unit,...
  14. [Error Code] Re: Bizhub c552DS with FS-526 SD-508 randomly throwing error code c 1151

    Many thanks for your response, 3ktlc !


    Okay, then I will first exchange the wiring harness from the control board FSCB and SD drive board SDDB.
  15. [Error Code] Re: Bizhub c552DS with FS-526 SD-508 randomly throwing error code c 1151

    sorry, it's a SD508 :rolleyes:
  16. [Error Code] Re: Bizhub c552DS with FS-526 SD-508 randomly throwing error code c 1151

    Hello,

    yesterday I had the same code (bizhub C552 with FS-526, SD-509).
    After replacing the stapler cartridge and carry out "Trouble reset" all works fine. But this morning the custumer called me...
  17. Re: C454e Jam code 9901 then "Pull out tray and set correct paper size and type"

    Thank you for your answer allen,
    but I do not know exactly what do you mean :confused:
    Could you please explain to me, what exaxtly should I have to do?

    best regards
    Joachim
  18. Re: C454e Jam code 9901 then "Pull out tray and set correct paper size and type"

    Hello,

    yesterday I had exactly the same problem with a bizhub 654e (counter about 800 K).
    Only when feeding from tray 3 (all others are working perfectly), after about 200 prints, paper jam...
  19. [Error Code] Re: bizhub pro 951 shows sometimes C22-22, toner concetration is too low

    Now, several days have passed and the machine is still running without a error code C22-22.
    Thus, the cause of the error was definitly M28.
  20. Replies
    17
    Views
    28,035

    [Error Code] Re: bizhub C224 has C2152 error code

    Yesterday I checked the ICP for a solder-bridge. There was absolutely nothing to see.
    So, the only cause left, is the possibility that a connector had a contact resistance.
  21. Replies
    17
    Views
    28,035

    [Error Code] Re: bizhub C224 has C2152 error code

    That's a good Idea!
    I used a special smd-soldering iron with a very thin tip and used strong magnifying glasses.
    I will again check the solder point closely.
  22. Replies
    17
    Views
    28,035

    [Error Code] Re: bizhub C224 has C2152 error code

    I removed the board and for a test I bridged ICP3 with a wire. After replacement the code 2152 has disappeared and the machine works fine :)
    Now, I removed the wire bridge and thougt, the code would...
  23. [Error Code] Re: bizhub pro 951 shows sometimes C22-22, toner concetration is too low

    First, I want to thank everyone who answered me!

    For a test I exchanged M28 with M29. After a half day, now error C22-26 was displayed. Now, it was clear to me, that M28 is the defective...
  24. Replies
    1
    Views
    4,550

    [Error Code] bizhub 363 shows C-9402

    Hello to all,

    my colleauge has a problem with a bizhub 363, error-code C-9402.
    When he deselected the ADF in the Tech-Menu, copying from the original-glass or printing is possible.
    Usually this...
  25. [Error Code] bizhub pro 951 shows sometimes C22-22, toner concetration is too low

    Hello to all,

    a bizhub pro 951 shows sometimes error code C22-22. The toner concentration is too low, that's why the prints are too bright.
    Unfortunately I have noch training on this model and...
Results 1 to 25 of 152
Page 1 of 7 1 2 3 4