Problem solved!!!
The cause was in the reversal unit. Unfortunately, an error encured during my first error Analysis. I had a reversal unit installed from a BH C224.
However, this unit has a...
Type: Posts; User: Laserbeam
Problem solved!!!
The cause was in the reversal unit. Unfortunately, an error encured during my first error Analysis. I had a reversal unit installed from a BH C224.
However, this unit has a...
@ Gaffers01
yes, I had already made this attempt. As soon as the paper become visible, I pulled it out under strong tension.
But the paper is still curled. Thus, the possibility that the paper...
Now I've changed following components:
vertical Transport assy (which includes the paper loop sensor above the transfer roller)
both registration rollers and bearings
registration actuator
CL6...
okay, this attempt I will do tomorrow!
@ emujo2
I have just installed a new tranfer roller, unfortunately still the old problem!
@ blackcat4866
I replaced the whole Fixing drive assy! In this assy there is a new CL8. no jam 30-03...
that's what I`ve tried with A3.
The location where the problem occurs is between fixing unit and paper exit unit. Between registration roller and etrance fixing unit the paper is not curled!
@ Phil. B.
the paper can be excludet! I have tested several qualities, the problem still exists.
@tsbservice,
yes, on the picture in the attachment, it`s A3-paper. That`s the best way to see...
Hello,
I am so desparate!
A bizhub C454e (total Count around 1,5 Million) shows the following problem: The paper shows about halfway a wave-line shape.
I habe already changed the following...
@ tsbservice,
yes, the one-way gear was the problem! It was seized on the shaft. I renewed the gear and the shaft and now everything works fine.
Thanks for your tip!
Hi tech51,
many thanks for your fast reply! Can you tell me more? What do I have to exchange? Do you mean the Paper Feed Drive Assy (PN A79JR70222) ?
Hello,
a bizhub C458 basically shows jam-Code 12-01 only from tray 2. Tray 1 is working fine.
If I remove tray 1 and watch the two feed rollers of tray 2, I notice that these didnīt rotate, a...
The problem is solved!
TB Drive Frame Assy (PN A92ER70200) was not properly mounted in the factory!
The positioning pins were not properly in their holes and this caused the assembly to warp.
This...
Hello,
a bizhub C3351 makes strange noises, only in color mode. In black and white mode, these sounds didn't occur.
I habe already changed following components:
Transfer belt, Fixing unit,...
Many thanks for your response, 3ktlc !
Okay, then I will first exchange the wiring harness from the control board FSCB and SD drive board SDDB.
sorry, it's a SD508 :rolleyes:
Hello,
yesterday I had the same code (bizhub C552 with FS-526, SD-509).
After replacing the stapler cartridge and carry out "Trouble reset" all works fine. But this morning the custumer called me...
Thank you for your answer allen,
but I do not know exactly what do you mean :confused:
Could you please explain to me, what exaxtly should I have to do?
best regards
Joachim
Hello,
yesterday I had exactly the same problem with a bizhub 654e (counter about 800 K).
Only when feeding from tray 3 (all others are working perfectly), after about 200 prints, paper jam...
Now, several days have passed and the machine is still running without a error code C22-22.
Thus, the cause of the error was definitly M28.
Yesterday I checked the ICP for a solder-bridge. There was absolutely nothing to see.
So, the only cause left, is the possibility that a connector had a contact resistance.
That's a good Idea!
I used a special smd-soldering iron with a very thin tip and used strong magnifying glasses.
I will again check the solder point closely.
I removed the board and for a test I bridged ICP3 with a wire. After replacement the code 2152 has disappeared and the machine works fine :)
Now, I removed the wire bridge and thougt, the code would...
First, I want to thank everyone who answered me!
For a test I exchanged M28 with M29. After a half day, now error C22-26 was displayed. Now, it was clear to me, that M28 is the defective...
Hello to all,
my colleauge has a problem with a bizhub 363, error-code C-9402.
When he deselected the ADF in the Tech-Menu, copying from the original-glass or printing is possible.
Usually this...
Hello to all,
a bizhub pro 951 shows sometimes error code C22-22. The toner concentration is too low, that's why the prints are too bright.
Unfortunately I have noch training on this model and...