Search:

Type: Posts; User: Arcking1968

Page 1 of 2 1 2

Search: Search took 0.02 seconds.

  1. Thread: Canon 7095

    by Arcking1968
    Replies
    5
    Views
    1,630

    Re: Canon 7095

    Gentlemen thanks' a lot for your help...The mahine is now detecting the finisher, the problem is the connector.
  2. Thread: Canon 7095

    by Arcking1968
    Replies
    5
    Views
    1,630

    Canon 7095

    Recently we bought a canon IR7095 to replace our old IR 105, but when we attached the finisher the machine can't detect it. can somebody help me how to program it.

    Thanks in advance...
  3. Replies
    5
    Views
    2,128

    Re: Sharp ar 5320

    I've encountered the same. Twice I replace the developer the third part I replace is the main board. The problem didn't return.
  4. Replies
    7
    Views
    3,094

    [Error Code] Re: Sharp MX-2700N H4-01 Code Not Going Away

    Akitu is right. Once I encountered the same problem I found out a blown fuse in the power supply. Another of our technician also find out the same trouble but the problem is the Triac also in the...
  5. Replies
    15
    Views
    1,573

    Re: wiping Hard Drives

    A week ago i formatted a MX-453 using 62-1 it took an hour. Make sure to write the meter reading because upon formatting the meter reading also will reset. Luckily I print the configuration and...
  6. Replies
    3
    Views
    682

    Re: erreur L4-01 AR-5015

    L4-01 refers to lock up motor but check the mechanical there might be a tight DV,DR or fusing unit.
  7. Replies
    2
    Views
    1,367

    [Error Code] Re: canon np3020

    Most probably if you ask the dealer of the spare parts you need for this machine it is expensive than a new machine.

    Canon NP means "no parts":)
  8. Re: after reassemble the TD sensor (2035) spill of dv powder

    If you cannot make some remedy to the hole, the best thing you can do is to replace the DV unit.
  9. Replies
    5
    Views
    742

    Re: check in ..

    Welcome:)
  10. Re: how to install 2018 scanner and i dont have any driver for scanner...where can i

    Welcome to the club...:o

    Try google...
  11. Re: Konica Bizhub 250 The screen does not work

    Try to upgrade the firmware...
  12. Thread: Black copy

    by Arcking1968
    Replies
    14
    Views
    2,304

    [Misc] Re: Black copy

    You've try almost everything, are you sure the parts you've test are all good? Did you test it one by one?and regarding black copy there is a totally black copy, and black copy with an image. Try to...
  13. Replies
    12
    Views
    1,988

    Re: AR-407 with f2-31

    If I'm not mistaken 44-2 and 44-4 is for drum mark sensor and I.D sensor, try to access the simulation and run this program and then adjust VR1 and 2 to plus minus 200. Usually even OEM consumables...
  14. Thread: Newbie

    by Arcking1968
    Replies
    4
    Views
    505

    Re: Newbie

    Welcome...:cool:
  15. Replies
    7
    Views
    578

    Re: Registered to help my poor secretary.

    Welcome...:cool::cool::cool:
  16. Replies
    3
    Views
    473

    Re: Newbies introduction

    Welcome...:D
  17. Replies
    4
    Views
    723

    Re: introduction..

    Welcome...:D
  18. Thread: Hi

    by Arcking1968
    Replies
    3
    Views
    565

    Re: Hi

    Welcome...:o:o:o
  19. Replies
    5
    Views
    764

    Re: Newbie checkin

    Shall I say test print?!, or test copy?! Welcome...:cool::cool::cool:
  20. Replies
    6
    Views
    601

    Re: Hello the world

    Welcome...:D:D:D
  21. Replies
    7
    Views
    621

    Re: hi ,,,, to al members

    Cheers...;););)
  22. Replies
    6
    Views
    569

    Re: A whole new world.

    Welcome....:cool::cool::cool:
  23. Thread: konica1213

    by Arcking1968
    Replies
    3
    Views
    739

    Re: konica1213

    Maybe the glossy picture paper cannot feed by the roller, try to use the bypass tray...:cool::cool::cool:
  24. Replies
    7
    Views
    1,192

    Re: mpc4000 copy issue

    You must concentrate on slit glass, or check the ADF guide that the paper is passing thru, maybe there is some dirt or color lines which is reflecting to the image.
  25. Replies
    21
    Views
    3,201

    Re: AR-208D toner is low message

    I don't think that there is a program or simulation to remove the toner low indicator...
Results 1 to 25 of 40
Page 1 of 2 1 2