Search:

Type: Posts; User: Max

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. [CQ] Re: Bizhub C300i Copy from Flatbed and single side adf

    Make sure the CCD is in the correct position. If I remember correctly you have -o+ depending on the paint mark on the CCD the mark needs to be in line with the line on the pin. (it's in the manual)...
  2. Replies
    6
    Views
    605

    Re: Konica to olivetti drums

    Develop and Konica are no problem, Everything is interchangeable. Olivetti is a pain and only on the i series. I never tried the sw as the other Olivetti chipped drums will not be recognised. Unless...
  3. Replies
    6
    Views
    605

    Konica to olivetti drums

    Perhaps it's been discussed but I can't find the thread now. We have quite a few Olivetti badged Konicas C450i. Lately, I have had difficulty getting the Olivetti Equilevent drum reset chips so I can...
  4. Replies
    29
    Views
    2,397

    Re: c250i stuck on boot screen

    Clean then format the ssd in the computer/using usb adaptor. Boot up with Q9 firmware. Works 9 out of 10 times. If not probably a CPU board
  5. Replies
    3
    Views
    538

    Re: Konica C360i incorrect toner

    I had this once. Had to replace CPU board in the end.
  6. Replies
    11
    Views
    2,313

    Re: Bizhub C224e OPC drum

    Obviously, the tone would play a part. The drum colour is a little off colour. The original drum should be darker green, which would suggest a compatible drum/ rebuild and depending on the quality...
  7. Replies
    4
    Views
    425

    Re: Olivetti D Colour MF364 Parts

    All interchangeable. Just swap the blue handle on the drum.
  8. Replies
    4
    Views
    612

    [Jamming] Re: Bizhub C250i FS-539SD jamming code J7225

    Churches tend to be very damp places. There are a lot of relay rollers in the booklet finisher too. Wd40 them all and wipe dry, plus try a fresh 80gsm paper.
  9. Replies
    5
    Views
    1,199

    [Misc] Re: Bizhub c 4050i Freezing and locking out

    Update boot rom. I would go with CPU board though.
  10. Replies
    6
    Views
    659

    Re: C250i C300i - C650i same box as anyone else

    I never tried it myself, but Data Direct do a rebuild kit.
    Konica Minolta BIZHUB C250i C300i C360i Black Drum Rebuild Kit 225K
    £49.00 + vat
  11. Replies
    15
    Views
    1,590

    Re: Bizhub C458 with a C-FA14 code

    Had this many times. Sometimes the copier doesn't accept working used HDD. What I tend to do when replacing an HDD is after replacement boot into trouble reset and go into the service menu. Then do a...
  12. Thread: C300i J2001

    by Max
    Replies
    4
    Views
    450

    Re: C300i J2001

    As the guide is transparent same as the mylar its quite difficult to see the edge of the mylar. The easiest way to check is if you run your finger upwards you will feel the bottom edge of the mylar...
  13. Replies
    20
    Views
    2,419

    Re: Color drums/IUs yield problem

    Set ACS to ON. Sw 25. Retracts the belt from colour drums when printing in K only. Less friction more life. Set calibration to black as default and perhaps extend power saving so it doesn't wake up...
  14. Replies
    10
    Views
    1,519

    Re: Bizhub C550i quality problem

    As mentioned above, set sw 153 to HEX 40. Do ACC after. Check the drum setting, default 0 and not minus figure in the service menu under the Imaging Process Adjustment option I think it is. +5 -5 ...
  15. Thread: Boot rom c308

    by Max
    Replies
    4
    Views
    1,299

    Re: Boot rom c308

    Got to the bottom of it. Turns out there are two different tar files. (Who knew) the one I used only worked on 8 series (458 and above)and i series.
  16. Replies
    2
    Views
    684

    Re: C-3350i, squeaking from exit section...

    Looks worse than it is. Twenty min job. Best to take it out and lube ever so lightly. Or go nuts and spray the shit out of it with wd40 ( not recommended)
  17. Thread: Boot rom c308

    by Max
    Replies
    4
    Views
    1,299

    Boot rom c308

    Hi All. I am trying to reset a c308 using a tar file but it's not taking it. I seem to recall having to update boot rom for it last time. I can't for the life of me find it on Konica tech site. I...
  18. Replies
    31
    Views
    8,300

    Re: I Series C250i C360i Stuck At 25%

    Tar file is the same as all previous models. C224 c308
  19. Re: I- Series Continued IQ issues (C3350i,C3320i,C4000i)

    Give it a good shake and turn the drive gear, Repeat 3 or 4 times. After initialisation do a dev agitation, and make sure the tray is out. Then do the calibration. Tends to work quite well. Every...
  20. Replies
    31
    Views
    8,300

    Re: I Series C250i C360i Stuck At 25%

    In my experience, I only had to replace the CPU board when the copier randomly locked up or randomly restarted. In one case it was a DF board that was dragging the copier down, restarting while...
  21. Replies
    22
    Views
    6,655

    Re: C308 printing black only

    Sometimes it's a glitch. Even if every life setting is turned off it still doesn't print. Switching it off and back on resets it. Sounds simple but it does work sometimes.
  22. Thread: STRGB C250i.....

    by Max
    Replies
    4
    Views
    913

    Re: STRGB C250i.....

    I tried it, but it didn't work. Doesn't boot or takes the f/w
  23. [Misc] Re: Bizhub 300i - Scan to email suddenly stops working

    There is a later firmware Q6. Try that as well. However, there is an issue with it apparently. The group sent email not working. Single and multiple are OK.
  24. Replies
    5
    Views
    415

    Re: +360i yellow/organge Background C-2554

    Hi. Don't swap used units from different copiers. The reason is as far as the copier is concerned nothing was changed and it's using voltages/charges/calibration for the old units. That is why you...
  25. Thread: B4020i

    by Max
    Replies
    6
    Views
    832

    Re: B4020i

    What message do you get when you press Detail? Possibly drum/Belt over life. If it is, there is an override for it in the service menu.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4