Make sure the CCD is in the correct position. If I remember correctly you have -o+ depending on the paint mark on the CCD the mark needs to be in line with the line on the pin. (it's in the manual)...
Type: Posts; User: Max
Make sure the CCD is in the correct position. If I remember correctly you have -o+ depending on the paint mark on the CCD the mark needs to be in line with the line on the pin. (it's in the manual)...
Develop and Konica are no problem, Everything is interchangeable. Olivetti is a pain and only on the i series. I never tried the sw as the other Olivetti chipped drums will not be recognised. Unless...
Perhaps it's been discussed but I can't find the thread now. We have quite a few Olivetti badged Konicas C450i. Lately, I have had difficulty getting the Olivetti Equilevent drum reset chips so I can...
Clean then format the ssd in the computer/using usb adaptor. Boot up with Q9 firmware. Works 9 out of 10 times. If not probably a CPU board
I had this once. Had to replace CPU board in the end.
Obviously, the tone would play a part. The drum colour is a little off colour. The original drum should be darker green, which would suggest a compatible drum/ rebuild and depending on the quality...
All interchangeable. Just swap the blue handle on the drum.
Churches tend to be very damp places. There are a lot of relay rollers in the booklet finisher too. Wd40 them all and wipe dry, plus try a fresh 80gsm paper.
Update boot rom. I would go with CPU board though.
I never tried it myself, but Data Direct do a rebuild kit.
Konica Minolta BIZHUB C250i C300i C360i Black Drum Rebuild Kit 225K
£49.00 + vat
Had this many times. Sometimes the copier doesn't accept working used HDD. What I tend to do when replacing an HDD is after replacement boot into trouble reset and go into the service menu. Then do a...
As the guide is transparent same as the mylar its quite difficult to see the edge of the mylar. The easiest way to check is if you run your finger upwards you will feel the bottom edge of the mylar...
Set ACS to ON. Sw 25. Retracts the belt from colour drums when printing in K only. Less friction more life. Set calibration to black as default and perhaps extend power saving so it doesn't wake up...
As mentioned above, set sw 153 to HEX 40. Do ACC after. Check the drum setting, default 0 and not minus figure in the service menu under the Imaging Process Adjustment option I think it is. +5 -5 ...
Got to the bottom of it. Turns out there are two different tar files. (Who knew) the one I used only worked on 8 series (458 and above)and i series.
Looks worse than it is. Twenty min job. Best to take it out and lube ever so lightly. Or go nuts and spray the shit out of it with wd40 ( not recommended)
Hi All. I am trying to reset a c308 using a tar file but it's not taking it. I seem to recall having to update boot rom for it last time. I can't for the life of me find it on Konica tech site. I...
Tar file is the same as all previous models. C224 c308
Give it a good shake and turn the drive gear, Repeat 3 or 4 times. After initialisation do a dev agitation, and make sure the tray is out. Then do the calibration. Tends to work quite well. Every...
In my experience, I only had to replace the CPU board when the copier randomly locked up or randomly restarted. In one case it was a DF board that was dragging the copier down, restarting while...
Sometimes it's a glitch. Even if every life setting is turned off it still doesn't print. Switching it off and back on resets it. Sounds simple but it does work sometimes.
I tried it, but it didn't work. Doesn't boot or takes the f/w
There is a later firmware Q6. Try that as well. However, there is an issue with it apparently. The group sent email not working. Single and multiple are OK.
Hi. Don't swap used units from different copiers. The reason is as far as the copier is concerned nothing was changed and it's using voltages/charges/calibration for the old units. That is why you...
What message do you get when you press Detail? Possibly drum/Belt over life. If it is, there is an override for it in the service menu.