I have two of these now that I am not able to log into the internal webpage in admin mode. Logging in from the op panel works fine. I talked to Konica and they had me set switch 25 to Hex 0. That...
Type: Posts; User: sauce_boss
I have two of these now that I am not able to log into the internal webpage in admin mode. Logging in from the op panel works fine. I talked to Konica and they had me set switch 25 to Hex 0. That...
I have one of these that will print fine from tray 2. As soon as you put any paper in the bypass tray it kicks a tray 2 jam doesn't try to feed from bypass or tray 2. I have tried a nvram reset and...
I was looking to re-chip black drums and use them as color as in the slower models in this series. After posting this I realized the higher end models have the color image units as all in one. Thanks...
Has anyone found these anywhere and tried them? I am looking for a cost saving measure to reset the life on these.
Did you find a solution for this? I have a 951 getting J1101 and J1201. Discovered today that the paper in the tray isn't lifting as it should and eventually the tires no longer contact the paper.
Looking for the repair manual for this I already have the troubleshooting manual but it doesn't have the info I need.
Did you ever find a solution to this problem? I am having a similar issue on a C7000.
This can also happen if they have the port in their driver set to LPR instead of RAW. Just something to check to keep it from coming back in the future.
Have a customer that scans sales orders to email. After one of their customers didn't receive their order they realized the scanner missed a page. They had 30 pages in stack only scanned 29 to email....
It's the transfer roller, replacing it should take care of the issue.
Give this a shot
Solution ID
2
Solution Usage
TAUS0703717EN*
Description
All duplex jobs spool completely before starting to print.
Solution
CAUSE: Paper Arrangement is set...
This has been resolved finisher entrance sensor was covered in paper dust. Tested good in service mode but would cause the jam intermittenly. Hope it saves someone the time it took me to figure it...
Thanks for the reply but no punch installed on this one.
Getting this jam in all modes staple sort ect. happens maybe once every 50 sheets sometimes more sometimes less. paper is stopping at the receiving roller. Have cleaned all the rollers in the...
Replacing the horizontal conveyance clutches took care of the issue. In talking to our Konica DSM he has said that replacing the clutches with part number 57GA82010 instead of the original clutches...
This machine only has 140k on it has starting getting these jams. I have tried replacing the registration and pre registration clutches. Found out it only seems to do this from the PFU trays 1,2,3...
Have a new machine has been getting this code since it was installed. Page goes through makes the copy but then indicates j66-14 after. Lift the lid and lower it and it clears. It's an exit jam. exit...
Makes a groaning grinding type noise when its initializing and calibrating. If I cheat the front door and pull the transfer belt away from the toners a little the noise stops. I replaced the belt...
I have one of these that is a new install. when stapling multiple pages the pages do not align correctly and one of the pages will not be stapled at all. It happens maybe 3 sets out of a 10 set run....
If that were the case I think I would still be able to print to it and the heartbeat sensor on the formatter would be blinking like normal instead of solid. Ordered memory dimm and firmware flash...
has the backlight on but nothing on the display, all three lights are lit on the panel. get an engine test page out. Was suggested to try a new formatter, tried that today and get the exact same...
Put the clutch in CL6 and it took care of the problem right away. Thanks for all the help.
Machine only has 188k on it, Dev isn't binding at all. I am going to try the clutch before the black dev and see what happens.
Black color dropping out in the middle of copy runs. Seems to be getting worse last time I was there black was almost never visible. Have tried replacing the black drum, transfer roller, transfer...
Guess I shouldn't just trust searching the knowledge base with the mobile app, as nothing showed up. Thanks for the heads up I will give that a shot.