hi everybody
does anyone know what is the purpose of the second (metal) blade in the IBT Cleaner assy in Xerox DC 250?
thank you
31928
Type: Posts; User: JimmyB
hi everybody
does anyone know what is the purpose of the second (metal) blade in the IBT Cleaner assy in Xerox DC 250?
thank you
31928
there is not ADJ 9.14, last one is ADJ 9.13 Belt Edge Learn
Max print image size of Xerox 250 is 323x480mm. When file is printed from computer which file is 323x480mm all dot are printed fine (image not cropped or have missed dots) but when long size is...
Does anyone know what kind of toner use old Xerox DocuColor 4 and Xerox Docucolor 40 machines.
are they compatible with Xerox DocuColor 12 toner or not?
thanks
i have NC for Xerox WC55 with not working ethernet card (chip is burned). does anyone know password for the Linux system? i am mean after Linux system boot, using altboot you can enter user...
here is the part num of Fuser Nip Clutch - 121K21612.
it is located on the back-left-bottom side of printer, looking from back.
check the fuser Pressure Roller clutch
iv got the same problem and it solved when replaced IDFE LVPS(Behind AC Driver PWBA).
The IDFE LVPS has two outputs:
•+5.1 VDC at 11 amps
•+12 VDC at 2 amp
look for "IDFE Low Voltage Power...
i need firmware files for WorkCentre Pro 35 to reload network controler, because it does not boot up.
i got for Xerox 3535, but that is not compatable with WP35.
thank you in advance
hi guys,
does anybody has a dump file of CRU chip for Xerox DocuColor 2006.
Thanks
and the machine is .....? ;)
check termistor, if OK read this:
NOTE:
This status code is stored in NVM location 777-160 and cannot be reset by Power Off/Power On. To reset this code, enter Diagnostics and change the value in...
look at from 1st pic, your 2nd BTR roll is in terrible condition (all is chapped).
1st, try to replace 2nd BTR unit or only roll, with good cleanig.
press "C"+"Green button" and enter pass:6789.
this will enter in Service Mode, but color calibration is not simple job if you do not have experience and some tools.
sorry it is my fault, yes only 66Mhz Celeron.
for X12 factory supply CPU is Celeron 433 and code is: SL3BA ---> Intel® Celeron® Processor 433 MHz, 128K Cache, 66 MHz FSBwith SPEC Code(s)SL3BA,...
Fiery X12 only support CPU Celeron 300-533 Mhz s.370. You cant use Pentium III, only Celeron with FSB 100Mhz.
good luck
The problem was in Control panel module.
look in SM for: Power Save and LED RAP
This RAP is used to repair failures in the Power Save and LED Circuit.
.
.
.
Preform the following:
•Go to...
on the back there is 5 fuses on Distribution PWB, 4 on Drive PWB and 1 on Tray PWB. all is OK.
there is another problem, but what is ..........
F3 is ok, all fuses is OK. checked 3 times:confused:
hi evrerybody
i have trouble with one Xerox DC12:
machine worked ok and turned OFF by power switch, after few hours when switched ON she does not work.
When switch power ON, only relays on back...
no way to upgrade bios of EX12 with FACI, only for X12 and XP12...
you need dongle and more......
10-377 External Heat Roll Control Thermistor Failure RAP
on ext.roll you have only 2 thermistor, probably you have replaced thermistor on Heat and Pressure roll.
on the top is EDIT PAD, not scanner.
to disable "insert coin" change NVM
700-096 PA Entry Key - Coin Kit
To enable or disable PA Entry Key Display (for Coin Kit)
0= OFF
1= ON
probably fiery is damaged doing cleanig ..... static electricity or some like that ...:(
does motherboard has speaker? if yes, and cpu is OK you have to hear beeps, if no, connect external speaker....
:D ... and bigger .... can i have DL link on PM please. many thanks