Couldn't agree more with Cipher, a Firefox plug-in would be good. I only use IE for firmware downloading. I was using IE11 but that stopped working so I had to install IE9 and now all is good.
The...
Type: Posts; User: Avalon
Couldn't agree more with Cipher, a Firefox plug-in would be good. I only use IE for firmware downloading. I was using IE11 but that stopped working so I had to install IE9 and now all is good.
The...
I can't see why EFI gave a link to download disk 2 and 3 if they are the same as the version 1 disks.
.
.
.
.
Just been out to the car to get my version 2 disks.Disk 2 and 3 are win764.1.1.1.15a...
Disk 1 and 4 are available from Ricoh site, disk 2 and 3 from EFI although they are rumoured to be the same as the E43A/83A. Alternatively order D7266613 and get the service disk kit.
I've not seen that error before but I can see you're on version 1 Fiery software. If you've done a machine firmware update to a very recent version the Fiery will need updating to version 2.Listed...
The driver is listed on the Download site under High End Production Printing.
The SR5000 V2 was a modded version of the finisher for the MPC6000 with special firmware and a speed adapter so that's probably why it isn't recognised.Can you see a firmware type when you print...
No offence meant guys.
Kind of agree with the idea that the Fiery is standard on the Pro model. In the UK you can have the GW, E22B and E42B on the Pro and the GW and E22B on the office version....
You're getting some bum information here. All Pro C5100 supplied in the UK have the GW controller but it is disabled because most have a Fiery connected to them. On the one occasion I installed a...
Load CWS4 that comes on the software disk or install it from the fiery itself.Browse to the ip address of the fiery and go to the downloads section if I remember correctly.
Had this once, always on the first print after coming out of energy save. Cured by increasing the ready temperature by 5 degrees.
The Latest firmware is the same as the Katana C1.5 or Pro machine as it's becoming known. We are getting a lot of calls on the helpdesk with problems in loading this firmware. If you upgrade to the...
I was asked a question by a customer today regarding a BK5010. At present they have a Pro C720 with an SR5000 and an MP9000 with an SR5000 and Plockmatic. Ideally, they want to replace the MP9000...
Are the 1050's different from the CPP 650/Pro C6500. I've flashed both of them with no problems.
On a similar note, can you load Fiery system software for an Ikon CPP 650 Pro 80 on a KM Pro C6500...
This is a known issue to do with the coating on the drums, TAUS1000512EN00.
The only recommendation is to fit the 102C drum part no.A0400Y4
Anybody have any suggestions for a C6500 with a Pro80 with the warning "sheets remain in saddle stitcher" coming up in CWS. The machine will still run a config page from the fiery and do a booklet...
I use a 20 gb drive out of a 4570 in a usb caddy. It will take every machine's software and is in the laptop bag ready to upgrade any machine in a flash. Never had any problems at all.
Had 1 account with 3 different sites using this crap on AF 3245C and AF3045 models.They all had jamming problems but each said none of the other sites were having any issues at all. We soon found out...
Did you set up the laser after you fitted it ? The manual does not tell you of any adjustments after replacing the laser but do a search in the service manual for the LD bias adjustment. Had to...
I run XP Pro and I had to install the Nethawk driver manually.I can mail it to you if you want to try it.
I wouldn't go near these if I were you...
I can find no info at all regarding a v2.1 for the Ikon Creo PowerPro Plus. I am installing one next week on a CPP660 (badged KM 6501) so will post back next week.
I use an old usb1 128MB stick and haven't had a problem, but I do remember being told that they can be quite fussy. You could always try using the ISW tool and a usb cable
PM me and I'll send you the latest firmware for this,
Mark.
Reload the system software and then select the language during the initial setup. I'm not aware of any other way of doing it.
I've had this before, the cusomer had 2 identical machines. When I put the GW board with fax option in the other machine it printed the faxes out. If I remember correctly it was the IPU board causing...