Hi,
After updating these models for chipless toners, we have faced a toner detection issue.
IRC3025i DCON Version = 14.01
IRC3125i DCON Version = 13.01
Any idea is welcome.
Thanks in advance.
Type: Posts; User: Rachid.Akli
Hi,
After updating these models for chipless toners, we have faced a toner detection issue.
IRC3025i DCON Version = 14.01
IRC3125i DCON Version = 13.01
Any idea is welcome.
Thanks in advance.
Thanks for your prompt answer,
The jam is with all types of media and sizes.
Regards.
Hi to all,
We are facing a strenge Jam code 0118 on duplex printing with three IPressC700 with the same customer. They are in the medical field. All their prints are on coated media. The issue...
Dear Sir,
Have a look on the position of the pick-up rollers.
Regards
Dear all,
A french proverbe says "It is better late than never".
The above error code E732-0021 may be displayed after opening and pulling the upper rear cover of the machine. This opertaion...
Dear Sir,
I have the same issue ( E732-0021) on my IRAdv8205 Pro. Please, can you share if you have any solution?
Best regards.
Hi,
• Down sequence when switching paper size
This down sequence prevents temperature rise of non-feeding area: The fixing temperature is higher in the ffixing film edges than it is in the...
Hi,
I don't remember well but the new reading glasses may come with adhesive tapes take a look on them. You can use the old ones for a verification.
Rachid
Hi,
This is common for this model. Replace the flat Cable between the Main Controller PCB and the Scanner Unit.
Rachid.
Dear all,
The test print shows a common issue to the four colors. There are two things which can be the cause.
1- Fixing assembly ( the fixing temprature and pressure can change the paper...
Hi,
I have found this:
1- Service mode > COPIER > FUNCTION > CLEAR > R-CON (RAM clear of CCD unit (CCD PCB)) >
2-Turn OFF and then ON the main power switch, and
...
Hi,
You may have an issue in the cyan toner supply system. The cyan toner can not reach the dev assembly. I suggest that you have a look on the cyan drum developing drive assembly. Replace the...
Hi,
Have a look in user mode and make sure that paper type is plain. The duplex is limited by the paper grammage.
Rachid.
Hi,
If toner and paper issues are excluded,
Fixing = Heat + Pressure.
1- During a printing procees, verify the fixing temperature which should be arround 180°C.
2- Execute a NIP-CHECK and...
Hi,
Try to explore paper quality. Paper dust may pollute the machine. Clean the machine air filter.
What is the activity of this customer?
Rachid
Hi,
Have you tried to replace the fixing motor?
Rachid
Hello,
The SCNT board may be faulty.
Rachid.
Hi,
VDM = 391 Volts will not give a blank print. I suggest to verify if the drum and Dev cylinder are turning.
Rachid.
[QUOTE=sniper2g8;560229]Where do I see the value of Vdm
Hi,
Diplay > Dpot
Rachid.
Hi,
For both error codes, I suggest that you clean the Toner vertical path of the Cyan Hopper. Otherwise, replace it. You can verify the steps to take the machine Service mode.
Rachid
Hi,
Have you tried something?
Rachid
Hi,
In this model, the laser lights on the blank image area. If there is no charge on the drum, you will have a blank print. So, what is the value of Vdm?
Rachid.
Hi,
There is a deflector sticking with the dampers. It is just before the fixing assembly. So, eliminate the two deflector dampers or replace them.
Rachid.
Hi,
Have a look on the two small metal sheets shown in the attached document and make them well straight. Otherwise, the metallic guide may retard a little bit the sheet of paper.
Rachid.
Hi,
I use the "Manage Attachment". It is available once you try to reply to a thread.
Rachid.