Search:

Type: Posts; User: harleyrider

Page 1 of 14 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    2,328

    Re: MX-FN27N Finisher

    I had a run of finishers where 5 out of 6 had that piece laying in the bottom of the finisher or stuck where it shouldn't have been. Not to bad to replace just take the top off the finisher and snap...
  2. Thread: MX-FN27

    by harleyrider
    Replies
    6
    Views
    3,219

    Re: MX-FN27

    firmware won't help if it is the same problem I had. remove unit and you can kinda see how to retime arms. I ordered a new one and made the old one in time like the new one to keep for future use....
  3. Thread: Mx3114

    by harleyrider
    Replies
    1
    Views
    595

    Re: Mx3114

    Replace PCL_PRG flash rom
  4. Replies
    14
    Views
    7,065

    Re: just curious...

    started in 1978 e-stats anyone remember those then savin 750 etc. Landa kits what a joke.
  5. Replies
    12
    Views
    3,124

    Re: Extreme Cold vs Car Stock

    This year mars 40 years in the field here in Illinois. I have never taken stock out and my company car sits outside.
  6. Re: Do you believe that Climate Change is real and caused by mankind?

    I don't know anything about all that s*** but I do know is has been freaking cold here. -24 without the wind chill. Just sayin LOL.
  7. Replies
    3
    Views
    1,379

    Re: Sharp al 2020

    not the same machine
  8. Replies
    7
    Views
    3,099

    [Error Code] Re: Sharp AR-M277

    He did
  9. [Misc] Re: ARM277 Fusing Unit compatible with AR271FU?

    In the USA we use AR272FU for that model.
  10. Thread: MX-M565

    by harleyrider
    Replies
    4
    Views
    3,045

    Re: MX-M565

    If I remember right Tray1_L is tray 1 jams and paper feed roller counter is higher than 200K
  11. Re: MX-3050,saddle stitching and cover mode

    yep we have a church that does that we just put it into favorites so they hit one button and go.
  12. Replies
    3
    Views
    841

    Re: Sharp MX-B401 fuser seating problem

    that "swing plate" probably isn't installed right. There is a little tab that sticks out and of the plate and it needs to be installed so that the swing plate will raise up to allow the fuser to go...
  13. Re: Any Gear-Heads here? (and not the plastic kind)

    Yep I use to drag race snowmobiles and motorcycles. Now I have slowed down to Harleys and vintage honda mini trails. Have 2 ct70's 2qa50's 1z50 1 vespa 3 Harleys. Still growing.
  14. Replies
    5
    Views
    1,298

    Re: MX-5141 shutter issue

    There is no clutch. Electromagnetic solenoid and developer is iron it gets into the solenoid.
  15. Thread: MX-FN27

    by harleyrider
    Replies
    9
    Views
    6,193

    Re: MX-FN27

    Thanks but those mylars already installed.
  16. Thread: MX-FN27

    by harleyrider
    Replies
    9
    Views
    6,193

    Re: MX-FN27

    have not tried it without finisher. Have tried new fuser. Found another set of mylars that sharp has put out for these. Installed mylars and we will see if that helps. Cleaned clutch's on front side....
  17. Replies
    2
    Views
    802

    Re: urgency sharp MX-M233D

    shifter motor trouble
  18. Re: MX-M503N has E6-11 and 2-2 and 2-1 grayed out

    could also be the doc feeder control board. I have had staples and paper clips blow them out.
  19. Re: MX-M503N has E6-11 and 2-2 and 2-1 grayed out

    If it was just a setting change you wouldn't get the E6-11 error code.
  20. Thread: MX-FN27

    by harleyrider
    Replies
    9
    Views
    6,193

    MX-FN27

    Anyone else having problems with these catching and turning the paper almost into a u shape when the paper exits the finisher? All the updated mylars are installed. Firmware is currant. Yes sponge...
  21. Re: MX-M503N has E6-11 and 2-2 and 2-1 grayed out

    best guess is the doc. feeder CIS isn't working. Check page C-2 in manual
  22. Re: Hi i need handy book for mx-m 564 please

    If you are talking about a Handy Guide I have not seen one for this model.
  23. Replies
    8
    Views
    1,545

    Re: Sharp mx m450n

    pull out top paper tray. There should be 2 screws at the bottom of the finisher to remove. Remove the screw you saw holding that lever and pull lever out. In the rear there should be 2 L brackets at...
  24. [Misc] Re: Will Sharp MX M754 Fuser work in a Sharp MX M654 (Same machine)

    yes they are the same fuser. MX-754FU1
  25. Thread: MX-FN27

    by harleyrider
    Replies
    6
    Views
    3,219

    Re: MX-FN27

    yep took that section out and like I said the claws were off a bit. Replaced and all ok. Glad I don't have to work on those every day.
Results 1 to 25 of 349
Page 1 of 14 1 2 3 4