Search:

Type: Posts; User: cobra

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    1,316

    Re: Blank copy on Canon IR Adv 6075

    Solved this problem by replacing the Drum Drive Assembly. This assembly includes the main charger terminal that caused the blank copy problem.
  2. Replies
    4
    Views
    1,316

    Blank copy on Canon IR Adv 6075

    I am fixing a Canon IR Adv 6075. There is no error but the copy is blank. I make a copy and stop the paper. There is no image on the drum. The primary charger assembly and the primary charging high...
  3. Replies
    7
    Views
    7,252

    [Error Code] Re: E061-0101 on Canon IR adv 6075

    Yes I have also checked the drum shaft fixing screw.
  4. Replies
    7
    Views
    7,252

    [Error Code] Re: E061-0101 on Canon IR adv 6075

    yes the primary charging assembly is new.
  5. Replies
    7
    Views
    7,252

    [Error Code] E061-0101 on Canon IR adv 6075

    I replaced the Main Driver PCB (PCB 2), Primary Charging High Voltage PCB (PCB 11), and Pre-Transfer Charging PCB (PCB 26) to fix E065-0001 problem. Now the error becomes E061-0101. Already check...
  6. Replies
    5
    Views
    5,864

    [Error Code] Re: E065-0001 on Canon IR Adv 6075

    Hi wcanonw. Yes I already did the SM procedure the first time I had this error. I didn't find any problem that's why I replaced the Main Driver PCB. But since the error showed again after a few...
  7. Replies
    5
    Views
    5,864

    [Error Code] Re: E065-0001 on Canon IR Adv 6075

    Thanks. I'll do that and get back to you.
  8. Replies
    5
    Views
    5,864

    [Error Code] E065-0001 on Canon IR Adv 6075

    I have fixed this error E065-0001 on a Canon IR Adv 6075 before by replacing the Main Driver PCB (PCB2). But after only 4 months the error E065-0001 showed again. Any ideas where I should check...
  9. Replies
    1
    Views
    4,167

    [Error Code] Re: E065-0001/E068-0001 on Canon IR Adv 6075

    E065-0001 was fixed by Main Driver Board (PCB2) replacement.
    E068-0001 was caused by loose connector from the High Voltage Unit to the Relay PCB (PCB5).
  10. Replies
    1
    Views
    4,167

    [Error Code] E065-0001/E068-0001 on Canon IR Adv 6075

    I am working on this Canon IR Adv 6075. The first error was E065-0001. I replaced the Primary Charging assembly but error remains. I removed and clean the Primary Grid High Voltage connector. Check...
  11. Thread: Part Number

    by cobra
    Replies
    0
    Views
    637

    [Misc] Part Number

    I have looked into the Service Manual of Canon IR Adv 6075 and it says there the Primary Grid High Voltage Connector (FM4-1006) and the Pre Transfer High Voltage Connector (FM4-1007). I looked in the...
  12. Re: Finisher-E1 not collating and stapling correctly

    Increasing the value of SORTER>ADJUST>SW-UP-RL fixed the problem. I believe rollers need to be changed. Thank you again.
  13. Re: Finisher-E1 not collating and stapling correctly

    Thank you for all your inputs. I will look into this and post back.
  14. Finisher-E1 not collating and stapling correctly

    I am working on this Canon IR Adv 6075 staple finisher-E1. The paper doesn't stack properly. The first few paper goes to stack processing tray but then the succeeding paper doesn't go down to the...
  15. Replies
    4
    Views
    3,864

    [Error Code] Re: Canon IR3080i E602-0001 error code

    Thanks this fixes the problem.
  16. Replies
    5
    Views
    2,407

    Re: IR 5050n problem on LCD touch panel

    The fix was Main Board replacement. Thanks
  17. Re: Out of Toner / Change Toner message in Canon iR1025iF

    This was fixed by DC Controller PCB replacement.
  18. Replies
    0
    Views
    482

    Sharp AL-1642cs DUP Transport Motor

    I am working on a SHARP AL-1642cs. I need to replace the DUP Transport Motor [parts code: RMOTP0012QSZZ]. Unfortunately it seems that this motor is no longer in production. Can you help me where I...
  19. Replies
    9
    Views
    3,302

    [Jamming] Re: Ricoh MP C3000 Jamming at Registration Roller

    Finally solve the problem by replacing the IOB. Thanks to everyone.
  20. Replies
    9
    Views
    3,302

    [Jamming] Re: Ricoh MP C3000 Jamming at Registration Roller

    Thanks finally able to update firmware after using a 1gb sd card and formatting it via Panasonic sd card formatter. Renaming the B230 folder to "romdata" and turning on firware update in service...
  21. Replies
    9
    Views
    3,302

    [Jamming] Re: Ricoh MP C3000 Jamming at Registration Roller

    I am doing a firmware update to fix this problem. But I am having problem updating the firmware of this Ricoh MP C3000. I recieved the firmware in zip file. Thanks to someone who sent me. Extracted...
  22. Replies
    9
    Views
    3,302

    [Jamming] Re: Ricoh MP C3000 Jamming at Registration Roller

    Thanks slimslob for a prompt reply. I will be replacing the registration sensor. The engine firmware is 1.10:01. I guess I have to update the engine firmware as well. Do you know where I could buy...
  23. Replies
    9
    Views
    3,302

    [Jamming] Ricoh MP C3000 Jamming at Registration Roller

    Our Ricoh MP C3000 is always jamming at the registration roller. Jam code J017. After check up I found out the registration roller is not turning causing paper z-folding at the registration roller. I...
  24. Replies
    3
    Views
    681

    Re: Canon iR1023 Scanner Problem

    Thank you northernlife. I'll do that then get back to you. I am thinking maybe I got a defective board from ebay. Any way to tell if the analog processor PCB is not working?
  25. Replies
    3
    Views
    681

    Canon iR1023 Scanner Problem

    I am called to check on a Canon iR1023 with no ADF. The first problem is the scanner won't move. Found out the reader motor is not working. I replaced the reader motor and the machine works OK. After...
Results 1 to 25 of 48
Page 1 of 2 1 2