Could also be a very dirty yellow 1st BTR.
Type: Posts; User: b003ace
Could also be a very dirty yellow 1st BTR.
The PM parts are highlighted throughout the parts manual in bold. The big problem is that the PM Kits are NOT listed in the manuals. They are listed, en masse, in a PM Kit document downloadable from...
Oh please, an SMC on any Aficio is child's play. But, then again, we have an awful lot of children playing in this sandbox sometimes. And my example of a Lanier 5622 (Af1022) was due to the fact that...
Just don't let the service manager find out you are Ignoring another tech's calls. After all, there is no I in TEAM. As a TEAM, you're supposed to support each other. Never mind that you've told...
I would be concerned with write trashing wear on an SSD. Some of the machines store ALL sort and multi-page jobs to the HDD which could cause premature wear / failure on the FlashROM in the SSD. I'd...
If you're having trouble retracting the housing for removal, you may have a bad drive gear retract cam in the rear drive. The dev will not come out unless it is retracted completely.
The other possibility for the accordion jams is that one of the plastic bearing retainer bars in the lower housing is broken / gone. The heat roller is a tight fit, and if forced, the bearings will...
Also, you might want to check that the correct entry chute is installed. If the bypass works correctly, you probably have the chute with a roller in it, which is required for the bypass. The (O)HCFs...
Make sure the system software is current (4) and the fuser cleaning web NVMs have been changed per the bulletin regarding long life web and new toner,
Another advantage to using the Type1027 instead of the PM Kit is the option for the customer to SELF-INSTALL, saving a service call all together. Leave the PCU alarm turned on and drop ship to the...
If you are using the newer long life cleaning cartridges, there are several NVMs that require updating to make the message more accurate. And the instruction sheet inside the box explains the STOP-9...
Depends on which 4110 HighCap you have. The ACH will, but only if it has firmware/software version 4.6.0 (label on board erroneously reads 4.0.6). The WFG will not work.
I don't believe this combination would work very well. The conversion from 8000 to 8002 required many modifications to the xerographic hardware, especially the drums. It also required many voltage...
Or you could buy into the manufacturer and get them to start building them better for techs. :)
I have a Ricoh 1022 equivalent, with ALL the features and options except finisher and paper deck. Anyone in the northeast got a used bridge, finisher, or paper deck to give away? :)
I'm so glad now that I turned down an offer from Ricon two years ago. I couldn't get a straight answer to questions about mileage rates and health insurance contributions. No ONE would give me...
I guess I did alright, I only missed the last one (ask for it).
You previously stated that this was a DF17... I assume you mean DF71 as I don't recall any DF17 on these machines. The DF71 is a SIMPLEX feeder. The duplex feeder is a DF72. Since only the 1018D had...
Another thing to check out is the cleaning area seals and the drum end seals. Both are prone to wear, the end seals also crush. They are available as service parts (although the 2035 and up with the...
Better yet, find a set of the little red plastic wedges that come in a new PCU and install them into the rebuild before installing the drum. Powder the drum and rotate it a few turns, then remove the...
'Put it in service mode and scan the sc history to find out what that wrench was for. That should send you down the right path.
Pull the tray completely out of the machine and check the white plastic jaw that actuates the tray lift. It may have a crack that allows the tray to lift incompletely.
Toshita, the product is shit, the manuals are shit, and their dealers are all subsidiary now.
I couldn't agree with this more. The only thing I would add to this is that it certainly seems the older machines are better built and last longer. Much like many of the older cars. Sure, the new...
Don't count on those "idiot" clauses. We had abuse and neglect exemptions in our contracts, but management NEVER enforced them. In fact, management would make us technicians look like fools. We would...