Hi
Are you sure the hdd is good? Some machine models will not function without a hdd. Also if it has removeable memory remove, clean the contacts and reset fully. Maybe worth a try.
Sent from my...
Type: Posts; User: Polarbear
Hi
Are you sure the hdd is good? Some machine models will not function without a hdd. Also if it has removeable memory remove, clean the contacts and reset fully. Maybe worth a try.
Sent from my...
So, this past Saturday as part of my new job, we attended a 4x4 fun day at Atlantis dunes on the West Coast of South Africa.
It gave me the opportunity to take my Amarok 4 motion on the sand to...
So after almost 30 years in the OA industry (17 September 2022 would have been), starting out in 1992 as a greenhorn laser printer tech at a franchise of Nashua in South Africa, then taking on...
Hi all
Just an update - switched on the machine this morning, made to sets of copies (with the new HDD) and the 3d set, BANG same fault!
I am out of ideas....
@Gift this is purely connected to the ac outlet. Nothing else tied to the controller.
It is doing my head in as the manual only says upgrade firmware or replace main board for this code.
Sent...
@Gift yes I did. 687-00 all over the place.
Will try known good hdd as per your suggestion.
Sent from my SM-N770F using Tapatalk
Hi All
I have an IM350 that does not want to play ball.
It started with its nonsense at the customer, where after about 2 days of working and standby, it would (once docs are loaded in the df...
Agreed.
Remove the whole pcu.
Press the blue lever on the side so the prinheaf lowers into the cavity.
Gently wipe with soft cloth.
Gently release blue lever to home print head.
Hi All
Dont forget these machines have a square tube between the toner supply "pump" and the dev unit.
If this tube becomes blocked (mostly because of dev unit failure) and the backed up toner...
Have you checked the blown fuse conditions for your machine?
To what screen does the machine boot?
If it is anything other than home, go to USER TOOLS > SYSTEM SETTINGS . FUNCTION PRIORITY and make sure it is HOME.
As for the data overwrite protection....
Have you checked that Access Control has not been enabled?
It would block all access to the machine except for the designated range set in the access control settings.
HI All
When My-Ricoh switched to Office 365 (Octopus), they split the training onto another site called Cornerstone Ilearn.
It turns out that both the product configurator and the device...
Hi All
On the previous My-Ricoh system, there was a timeline for each model device, with introduction and termination dates, and it's predecessor and replacement models, in a graph layout.
Does...
Does this one have the triangular metal catch on the right side of the drawer rail? On mp2500 these were very soft and would bend causing extra play when the drawer latches closed. The slightest...
Gift I think you are right. You cannot have wired and wireless lan active at the same time.
I am confused.
The device is not detecting toner at all. How is turning toner END detection helping?
Hi.
What happens when you open the ADF cover? - does the machine complain?
I second the comment on the shark fin sensor flag, that will make the machine disable the df thinking it is not...
At this point, I would look at the BICU, as it controls all the workings in the machine. The controller is mainly and interface between the device and the outside world - almost like a computer. That...
Hi all
Years ago with the MP2352 series, when the guys were in a corner with noisy hot roller bearings, they would cut a strip of paper as wide as the bearing and then flip the bearing and...
We had a similar issue.
If I remember correctly, it was an issue where all the firmware was not up to date and the difference between the ages of the firmwares caused it to crash.
Updating all...
Hi
Those printers had software that needed to be installed to access most features on it.
I am with the other poster on the arrows being held in for a set amount of time, so access service...
Hi all
That sensor looks like an MP201 paper end sensor?
Should fit right in.
Hi
What do the bags look like?
Can one not find a compatible?
Yup the dev tank was toast....
Sent from my SM-N770F using Tapatalk