Search:

Type: Posts; User: MCBIG

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: Skew tray 1 C364

    by MCBIG
    Replies
    10
    Views
    4,674

    Re: Skew tray 1 C364

    Sounds like an issue with registration roller bushings. Had one doing this a few months back and new bushings and reg roller fixed it. I also replaced the housing the registration roller sits in.
  2. Replies
    10
    Views
    1,691

    Re: Bizhub C450 Networking?

    I would disable and remove the Fiery. Enter service mode, go to system 2, image controller type, change to controller 0. You will then be able to change network settings via the machines interface.
  3. Replies
    35
    Views
    10,594

    Re: C552 Service mode password

    The default is 9272 (4) times. Like this:

    9272927292729272
  4. Replies
    4
    Views
    1,034

    Re: bizhub C250 Counter List won't print out

    Had this on a C450. Reloading firmware resolved it.
  5. Bizhub C353P Authentication / Service Mode / Network Settings

    Hi,

    Got in a Bizhub C353P as a "throw in" with a load of other machines. I have plenty of experience with the regular C353, but zero with the p model.

    The machine will not allow me to access...
  6. Replies
    2
    Views
    489

    Re: Bizhub C351 Doc Feeder Inop

    You will probably find a fuse blown on PU-1... but something made it blow... Like a shorted ADF control Board.
  7. Replies
    2
    Views
    1,078

    Re: driver for as400 bizhub 420

    Try the IBMSNMPDRV system driver.
  8. Replies
    3
    Views
    617

    [Error Code] Re: sc29-08 Konica 8050

    See Attachment.

    15111
  9. Replies
    13
    Views
    3,834

    Re: Konica 7145 F-26-03

    You are probably going to have to replace the developer. This problem can be a few different things but that far and away most often will fix it. It could be that the toner bottle is not turning, or...
  10. Replies
    2
    Views
    770

    Re: develop dfc 110 c 0030 error

    Would that be like a CF900?

    If so:

    Code references developer drive motor malfunction. So, check motor and see below:

    PROBLEM:
    Drive motor failure during pre-drive, C00** error codes...
  11. Replies
    9
    Views
    10,263

    Re: Konica c352 account track and authentication.

    See the below attachments:

    15023

    15024


    I will send you a private message with more info.
  12. Replies
    9
    Views
    10,263

    Re: Konica c352 account track and authentication.

    Authentication/Account Track has to be enabled in the print driver under the configure tab. If you do the "acquire device info" it will not detect that you have Authentication/Account Track enabled....
  13. Thread: Feeder jamming

    by MCBIG
    Replies
    5
    Views
    1,037

    [Jamming] Re: Feeder jamming

    Do you have the scanner locked? Does the scanner move? The scanner being locked will cause this.

    I am assuming this is an abort code and not a standard trouble code since you put dc0652 and all...
  14. Replies
    4
    Views
    1,097

    [Jamming] Re: bizhub 350 pc402 jams

    Support Kit # A11UR92600
  15. Replies
    1
    Views
    963

    Re: Konica Minolta BizHubb C253

    I think if you scan in black, you will get G4 compression. Seems I recall reading this. G4 not supported for color scanning to TIFF.
  16. Replies
    1
    Views
    641

    Re: bizhub 500 skewing adjustment

    Not sure on your question, but I'd say there is a good chance that the skewing is being caused by the door not latching properly on the PC-402. Check the latches.
  17. Re: Windows 7 print driver for Konica 7022 with IP422 ???

    TheOwl is on the money! I have to walk IT guys through that procedure far too often.
  18. Re: Konica Minolta Bizhub C 352 Waste Toner Bottle Trouble ! HELP

    ^What Darren King said should lead you to the promised land. I ran into a similar problem several months ago. Got to get something back in there and clean those sensors... maybe compressed air.
  19. Replies
    3
    Views
    5,270

    Re: magicolor 1690mf code 0310

    I've only looked at one of those a few times so I can only offer this:

    Subject:
    0310 error code during printer operation.
    Description:
    0310 error code.
    Solution:
    CAUSE: The SOS signal is...
  20. Replies
    4
    Views
    5,820

    Re: Bizhub 600 Jamming

    Subject:
    Jamming consistently from Tray 1, Tray 2 and the bypass. Feeds properly from Tray 3 and Tray 4. Jam code may be either J1701 or J1001.
    Description:
    J1701 or J1001. Jams every time from...
  21. Replies
    10
    Views
    3,381

    [Misc] Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    When I run into this situation, the developer unit is usually not original to the machine... as in taken from another machine. You will have to change the developer unless you have the original unit....
  22. Replies
    10
    Views
    3,381

    [Misc] Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    Toner Density sensor issue. Either too much or too littler toner in the developer. Have you swapped in a developer unit from a different machine? That will cause this error. Only fix in that case is...
  23. Replies
    10
    Views
    3,381

    [Misc] Re: KONICA 7022 Showing "PLEASE ADJUST L DETECTION"

    Well, run L Detect. It is in 36 mode. Get into 36 mode by holding down 3 and 6 and powering on the machine.

    Are the paper trays grayed out on the control panel? Does the machines mechanical...
  24. Replies
    4
    Views
    1,097

    [Jamming] Re: bizhub 350 pc402 jams

    I've ran into similar problems on many occasions with the PC 402. Recently on a machine with only 89k.

    Most likely, the one way clutches on the pickup and/or feed rollers have failed. I used to...
  25. Replies
    2
    Views
    1,228

    [Misc] Re: Power on the Controller error

    If I ran into this issue myself, I would probably start by reloading the Fiery System code....
Results 1 to 25 of 36
Page 1 of 2 1 2