So,
We have a real world example of networked printers on a server crashing a network…. They cleared the print queue and the network came back up.
So, we aren’t going to put the field...
Type: Posts; User: nogood boyo
So,
We have a real world example of networked printers on a server crashing a network…. They cleared the print queue and the network came back up.
So, we aren’t going to put the field...
Yeah i was afraid of that. Unfortunately we have waaaayyyy to many field sites for that to be a viable option at this point.
The major concern is, with the topology of the field sites and the...
Hey Folks,
- we have many remote sites with printers
- currently printers are printing direct IP locally at said remote sites (so there's no traffic on the WAN)
- we cant put a print server on...
Also: lol at my last post on this subject. Oh, how i've grown.
BUMP.
Revisiting this problem. Thought that i had it fixed without replacing the Punch Controller PCB... looks like i was wrong :)
Does anybody know where in service mode i perform a sensor...
Figured it out,
The shaft of the mag roller isactually bent just ever so slightly. Causes the roller to pull away from thedrum just a little bit.
Not sure if I caused this or not(50+ print...
What are the odds that the dev unit on a 6265 is the same as a 6055? Does anybody know? If this is the case i can swap out with another machine on site and see if the fault follows the part.
They...
Good morning everybody :)
Brand new machine, just set it up and installed. (see attached PDF... i printed off multiple test pages so you can see the repeating pattern)
I made the rookie mistake...
Success :)
Swapped out the power supply. Working perfectly.
Thanks for all of the advice.
So this is the board in question, and the fuse that i have highlighted in Red is the one that i have already replaced once, and fried.
23864
23865
I have since purchased a new Power Supply...
Okay,
So i pulled out the High Voltage Power Supply (its weird the board says High Voltage PS but the service manual says its the Low Voltage PS??) and inspected it... found a burnt out 8 amp 125...
Good afternoon all,
Machine will not power on :(
This machine was located out in a small field office. There was a bit of a wind storm about a week ago and apparently the machine stopped...
Machine is doing it again!
Ran okay for a couple of weeks then the same error code.
any thoughts? A sensor i missed?
replaced all of tires and cleaned all the appropriate sensors, did the the trick.
thanks for the advice!
HP 4700
Prints out one page then prompts with the code 13.01.00
Any ideas? A point in the right direction perhaps?
Thanks heaps,
Thanks for the advice with this!
I started stripping apart this machine this morning and discovered little bits of rubber along the bottom of the carriage unit... remnants of teeth from the...
thanks but i already have a full service manual...
the problem is that i run a test to determine the error code and the error code (in the service manual) tells me to run the same test for more...
Good evening everybody,
I have an HP Plotter giving me an issue i need a little bit of help troubleshooting...
History:
I was called in for a paper jam... the paper had jammed, the users...
Thank you for the troubleshooting tips with this,
I will keep you posted on the progress of this.
-Nogood
Good afternoon everybody...
I have an HP 5025 that is printing out blank pages... both copies and prints, sky shot and engine test both blank. The machine is about six years old, at first i...
Just required a good cleaning, fixed the issue first shot.
Thanks again for the advice with this.
okay, that makes sense.
i was going off the life on the p-prints... last page
MISC
*-DRM-LF
one machine would reach 400-450 and another reaches around 190 - 210 and fails.
Yeah, I have one machine, the drums fail at about 450... and another machine, the K-drum has failed at about 150
How do i check the counter settings... does this machine read a an 11X17 as one...
First i opened up the machine and verified the laser range settings were the same on the laser units as they were in service mode, then i used service mode to set all lasers to the center position,...
Spectacular,
As always, above and beyond when it comes to helpful advice.
Venture a guess as to what the other image fault might be?
Thanks Heaps,
Nogood.