hello everyone
this machine won't print from tray 1 - someone has set "tray 1 config: Paper Size" to CUSTOM (rather than 'cassette size') as per the attachment
62072
i'm assuming one has to...
Type: Posts; User: aAandy
hello everyone
this machine won't print from tray 1 - someone has set "tray 1 config: Paper Size" to CUSTOM (rather than 'cassette size') as per the attachment
62072
i'm assuming one has to...
thanks gentlemen,, suspicion confirmed,, main controller it is
hello everywon
when this machine is turned on, the engine runs up normally, scanner and ADF initialise normally, fans operate, main power and power save are lit but no display
checked 5v 12v...
i never use aftermarket toner with these machines - too many print quality issues and you can end up chasing your tail looking for the cause of unusual print quality issues,,,,,
silly question, but are they OEM drums? or aftermarket? if aftermarket and other suggestions don't work, go OEM
hello everyone! and Happy New Year!
this machine has me stumped and i'm hoping someone has seen this fault before! this machine will network print fine, prints counter fine, prints service mode...
go to control panel, devices and printers, right click on the device and select "printer properties" then select "port" - is a WSD port being used? if so change it to a TCP/IP port
doesn't even print test pages? are you referring to internal test prints? if it doesn't print internal test pages it has absolutely nothing to do with the network or anything external
what...
thank you all for your input, very much appreciated!
i dismantled the print head (strange name for a laser unit) removed and dismantled the polygon motor and cleaned and polished both the bush,...
hey everyone - Merry Christmas!
i attended this machine and the Upper Fuser Roller was scored by a picker finger leaving marks down the prints - so i replaced the UFR, bushes, drive gear, picker...
the lines do not show in mono prints or copies - silly question perhaps, but why would the print head only produce yellow lines?
hey everyone - Merry Christmas in advance!
this machine is putting random 'edge to edge' yellow lines across the page, different line widths, different spacings and it doesn't matter which paper...
just looked through the manual, there is only one Out-Of-Paper sensor, the other sensor is the Output Tray Sensor - you may have a broken flag, damaged ribbon cable, sick Bundle Board or sick Main...
hello everyone
as i am not a HP partner, i cannot access the HP WISE portal to find the relevant Control Panel Message Document (CPMD) for error code specifics
is anyone here able to access...
hello everyone
i need to perform head clean and possibly printhead recovery, but there is no "Device Maintenance" icon on the home screen
logged in, still nothing, any suggestions?
thanks in...
hello everyone
attended this machine for banding, performed head inclination & head slant (no adjustments required), perform media feed calibration & PG adjustment, test IM sensor OK, test PF...
thanks for your response (sorry for the delayed reply, i didn't get email notification)
58810
the machine recently had a new ITB assembly & cleaner unit fitted to due tracking belt rubber going...
hello everyone!
i have a minor colour registration issue with cyan being approx 1/2mm out in direction of travel, but for the life of me i can't seem to find a method of calibrating colour...
hello people
fitting new devs to all 4 units but don’t know which NVM to reset dev counters
any help much appreciated
forgot to mention, i re-checked my toner drive install & all connectors, re-seated all connectors on the controller board and display & re-mounted all RAM NVRAM etc etc
hello everyone
attended this machine for error E025-0468, got a replacement C/K toner bottle drive, fitted it OK, powered the machine up, it ran up and printed "Communication management Report...
i suspect the one you pictured is the 'brasso' variety, far too abrasive
in Australia there is Brasso designed for polishing brass which is rather abrasive and not to be used - silvo however is...
thank you Slim, much appreciated
thanks for the response!
i've not used factory SP on machines with the 806182 SP entry, is it the same as for the machines with 107 SP entry?
thanks for the response, i forgot to mention the machine is in a shed with no network