the LED count up to 00 as they always have.
I need to reset the machine I am thinking.
sorry, thought this was at help board.
I am awaiting a techie call but thought it might have been...
Type: Posts; User: Capodastra
the LED count up to 00 as they always have.
I need to reset the machine I am thinking.
sorry, thought this was at help board.
I am awaiting a techie call but thought it might have been...
Thank 6ou for your help with this.
I am not that techno savvy with the service mode commands and would appreciate step by step guidance how to disable the controller in service mode, Lao what do...
I think yu are thonking to search within the Workstation software.
Problem is the Command Workstation asks for an IP address to add the fiery before it will go any further when opening up and as I...
Thanks so much for the help.
So I have disconnectted all Ethernet network Cables; shut down and restarted the machine but still has the same issue.
Just wondering if its possible to reset the...
I think I might be in a bit of trouble!
I am running Command Workstation on my iMac running Mac OS 10.6.8 and linked to my Konica Minolta Bizhub C451.
The Command Workstation software kept...
Still does not work going that route maybe it's just the Mac OS?
I have finally found the solution!
I cloned ths spare hard drive from my Mac Tower which runs Yosemite.
It held the old versiojn of Wokstation.
Started up the iMac from that drive,...
So, I have tried the IP address and it will not connect from my Mac runnning OS Mojave. Tried from the iMac running El Capitan - failurr!
On one of my previous drives there is an older system...
Thank you again for your help in replying but I have no Fiery software other than (a) 'Fiery Software Manager.app' which does not work (either on my Mac Tower running Mac OS Mojave or my iMac running...
Tried an older download [FieryApplicationsPackage3e.dmg] but it gives me an error 'installation failed. The installer could not install the software because there was no software found to install'
...
Thank you for your help.
How do I go tothe IP address (192.168.1.198) - I have tried typing it into my browser but says unable to connect?
Thansk in hop.
Barney
HELP PLEASE!
I had to delete my Command Workstation 5.8 (am running Mac OS Mojave) and even though I downloaded the installer [FieryApplicationsPackage44.dmg] it just will NOT install. My EFI RIP...
Thank you so much for your reply.
I am not an engineer so the task of TOTALLY dismantling the unit is formidle for me. Also the stages to dismantle this unit aren't in the field manual sadly for...
Yes, have done that at the beginning and then took it apart to make sure it was "super clean", but still no response. I have also checked and move the RAM around, but no jy.
Just wondering if it...
Hi,
My faithful old C451 is now giving me issues as the control panel touch control is not working.
I have carefully taken it apart to clean the area under the bezel and replaced it = all still...
So the transfer unit has arrived and replaced but the whining is still there. BD((
Seems there are a couple more parts still needed.
Bit frustrating when the internet firm whom I tried...
Zesti, I do believe you are correct.
I was finally able to contact a colleague who was a Konica engineer and now works for Zerox.
He has looked at the machine and determined it to be the...
Hi,
My C451 was printing ok, the a repetitive clicking noise and finally a continuous whining noise like something was jammed.
now it wont work and just makes the whining noise when i switch it...
Sorry, I do not agree about black looking fine- the registration is miles out.
It only happens with PDF files.
Any pointers please.
Here is a scan of a pront where the registration points are all pretty good but the black is way out of register.
From InDesign I can create a postscript file of the...
I have done the expert adjustment to correct minor registration issue but something that is beyond my knowledge is happening.
The registration marks at each end of the long edge are in fit but the...
Thanks for all your help.
After numerous calibrations and adjustment sin Acrobat it has disappeared.
BD)
I can't seem to get calibration right.
There is a slight magenta and cyan tint (about 4%) in solid yellows, so I cannot print a solid yellow alone . . . anybody got any ideas . . . please?
...
Can anyone give me any pointers with this please?
I am on a Mac running OS 10.6.8 with Fiery Command Workstation 5.
I have created the postscript file from INDesign CS 5.5 and when I set it to...
OOPS sorry Elmo if that was offensive, was not meant to be, did not know that this was a board only for techs, thought it was was for any business that had a machine too.
Sometimes in my...