go into Additional Functions>Common Settings>Limited Functions Mode and select "OFF".
Type: Posts; User: Hopper
go into Additional Functions>Common Settings>Limited Functions Mode and select "OFF".
parting out machine, fuser, etc.
Yes, glass copies were clean. Go figure.
Solution was to clean the contact (scanner) sensor.
Lower fuser bearings locked up. I was able to get out the door by oiling the bearing. Katun has come up withe a lower fuser roller with pressed on bearings Katun pn: 39155.
Sent from the copier with no computer involved.
I have just sent a referb'd ir 3225 with Universal into the field. The end user is getting 2 thin black lines across the header of the page. About 3" inches down and 1/2 inch apart. Both copies from...
So here is where I am at on my hopper not spinning. I have found that it does rotate if I pull out on the bottle. The cams look good, no cracks. It is just not sending it home all the way. If I use...
OK, got the finisher off and looking at the cam. Does it just take two screws and it comes of or do you to pull the whole shaft?
OK, per someone's past post I pulled the toner a little forward and the toner did rotate. So it must be the cams. How do you get at the cams with an S-1 internal finisher installed?
TIA
Thank you. My developer comes up empty and it seems the toner bottle is not rotating. The serial number comes after the cam change that I read about here. In SM part check motor set to 5 and door...
Can someone post data bit for toner in developer in SM I/O section.
Thanks, I am missing that one service manual.
Anything newer than the 2230 takes a hard drive with a Canon file on it. DO NOT FORMAT. We've been getting all of our replacement 3225 and 3245i hard drives ready to go from Hytech Dealer Services in...
A) Call a tech.
B) Turn of the lights and go home.
C) Attach line in from the street to copier "line", put postage meter on "ext".
Problem solved. Got this info from another tech. Removed developer and there was a pile of toner on a mylar strip over the doctor blade of the developer. Their solution was to clean off the pile...
Problem solved. Got this info from another tech. Removed developer and there was a pile of toner on a mylar strip over the doctor blade of the developer. Their solution was to clean off the pile and...
I have a IR 5075 with a line. This scan does not do it justice. It is as thin as a hair and is coming from the print engine of the body. I replaced the web and UFR looks fine. Did a stop copy and it...
I have a IR 5075 with a line. This scan does not do it justice. It is as thin as a hair and is coming from the print engine of the body. I replaced the web and UFR looks fine. Did a stop copy and it...
I have done a number of these. You need to fin out the coin machine color code. With Canon it is usually a 4 pin connector. Two pins are enable and two pins are click. The enable brings the copier to...
You got me on this one. Maybe it shows the fax and does not need transmit info. Try turning the image off.
*-Additional functions
left column Report settings
Settings on left column
Fax TX-...
Back in the days of the IR 330 there was a 5v fuse on the board that would blow. I/We replaced/repaired the fuse and all was well. I do not know if this applies here.
What were the key strokes you used? Did you do ERR clear?
rather new to these items. was wondering if the feed tire with the gear FB6-3406 and FC6-7083 are inter changeable?
We have a number of Canon IR 3225i machines for sale. Located in Raleigh NC. Mr. Watts 919-872-2636
I have a Canon IR 3235 copier that was received with no hard drive. Purchased a Hytec drive with boot sector. Installed machine software and machine is up and running with Universal send. This tells...