Search:

Type: Posts; User: DavePo

Page 1 of 13 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    603

    Re: MX-M753 Fuser Web Feed Rate

    We had success by setting A to zero, and C to 10. Leave B at default.
  2. Replies
    3
    Views
    1,982

    Re: FN27 close front cover message

    Have you verified that you are getting 24VDC at the switch? If missing you would get that message.
  3. Thread: Cold Mx 850rt

    by DavePo
    Replies
    4
    Views
    860

    Re: Cold Mx 850rt

    We have had that for 5-10 years now. Sharp says no problems. I usually threw them in a microwave for about ten seconds warmed them up enough to stay put.
  4. Replies
    4
    Views
    639

    Re: 6240 developer unit swaps.

    It appears that they are the same.
  5. Replies
    16
    Views
    2,399

    Re: Flaring blacks MX-3070

    Looks a lot like a Laser Unit issue with the black beam.
  6. Replies
    10
    Views
    4,920

    Re: Staple waste box is full

    Fixed both machines with the message by also downgrading firmware. Have 1 stapler that is bad however, now doesn't recognize staple present. Awaiting replacement.
  7. Replies
    10
    Views
    4,920

    Re: Staple waste box is full

    I have it also on 2 7002i's with DF7110. Hotline wasn't helpful. Ordering staple unit and finisher control pwb.
  8. Replies
    7
    Views
    1,980

    Re: MX7500 blowing toner like crazy

    What is the humidity level reading in TC 44-14? We had one last year in January that did this exact thing. The Humidity in the room was less than 10%. When humidity gets that low machine can't...
  9. Re: MX-B201D Saying "Install Toner Cartridge" with new cartridge

    Check the connector in the rear frame that toner plugs into. They can be bent out of position.
  10. Thread: M6035cidn door

    by DavePo
    Replies
    6
    Views
    955

    Re: M6035cidn door

    We had one that the safety latch for the Doc Feeder was broken. It is needed to keep adf from opening when toner door is lifted. The latch is in front left corner and actuates a latch in front left...
  11. Re: No find ADD(Y) in ADDRESS BOOK on webpage of MX-M452N

    System Settings - Image send Settings - Enable/Disable Settings check if anything disabled.
  12. Replies
    5
    Views
    1,115

    Re: Opinions on the TA 3252ci series?

    Have had a magenta developer unit, a yellow developer unit and a black developer unit fail. The magenta happened at initial power up, a seal was pulled out of developer unit and into drum unit. The...
  13. [Error Code] Re: MX 3501with more involved F2-64 any help appreciated

    Another thing to ponder. We have had several 2300 2700 3501 and 4501 machines develop the f2-6X error. Upon investigation we started to see that the toner motor would run backwards every other time...
  14. Replies
    26
    Views
    4,059

    Re: Good tool magnetizer?

    I use a magnet out of a old HDD. Put it in a pouch behind my screwdriver and every time I put it away and remove it gets magnetized.
  15. Replies
    10
    Views
    2,812

    [Jamming] Re: Mxfnx9 jams second page every time

    We are having same issue FPDD_S jams when trying to staple. Sharp said try sensors (have replaced all no help). Try greasing rail for stapler no help. Have replaced board also still same issue....
  16. Thread: Eaglecam

    by DavePo
    Replies
    99
    Views
    28,979

    [Video] Re: Eaglecam

    Not to hijack the thread or change subject, I swear by Rain X Bug Remover Washer Fluid for summer driving. Doesn't completely get rid of all of the mess but it's better than anything else out there...
  17. Replies
    5
    Views
    5,487

    Re: FS-2100DN not connecting to network.

    Neo your where on the ball. The problem was one of the pins in socket was bent. Another issue was that HTTP protocol was turned off. Straightened pin and enabled HTTP and all is good.
  18. Replies
    5
    Views
    5,487

    Re: FS-2100DN not connecting to network.

    My issue is that i am not showing any link on the switch and status page shows no connection also. This is either dhcp or static.
  19. Replies
    5
    Views
    5,487

    FS-2100DN not connecting to network.

    Have a new FS-2100DN fresh out of box, when plugged into network doesn't show any network connection. Status page shows under current LAN interface not connected. Have tried different cables and...
  20. Replies
    1
    Views
    592

    Re: Pcounters and MXM365N issues.

    Found issue to be under User Control, Card Type/Card Reader Settings. The check box Use IC Card for Authentication needs to be checked.
  21. Replies
    1
    Views
    592

    Pcounters and MXM365N issues.

    Anyone out there using PCounter software with Sharp MXM365N imagers? If so are you using a external card reader? Any problems? We have installed four in recent weeks all have issues with reading...
  22. Thread: SharpDesk issue

    by DavePo
    Replies
    18
    Views
    6,537

    Re: SharpDesk issue

    I agree completely, I believe also that Sharp sees this as a large loss of revenue. Cant tell you how many times customers have bought new machines and added the new license to their existing license...
  23. Thread: FOOD

    by DavePo
    Replies
    235
    Views
    68,122

    Re: FOOD

    Mine is not a Kitchen top toy. Though I love to cook with it. My Smoker and Grill.
  24. Replies
    8
    Views
    11,676

    Re: Updating firmware via webpage (mxm363n)

    First post and wants password?
  25. Replies
    1
    Views
    1,070

    [CQ] Re: CQ and F2-52 Code

    Cause:
    Drum phase sensor trouble.
    Harness and connector connection trouble.
    Drum drive section trouble.
    PCU PWB trouble.
    Check & Remedy:
    Use SIM30-1 to check the operation of "DHPD_C",...
Results 1 to 25 of 301
Page 1 of 13 1 2 3 4