no problem Phil.. delete this thread its just a line across the page when I print. I will re clean everything after the next print run.. read the file link and still cant upload the scanned pic.....
Type: Posts; User: zflash7
no problem Phil.. delete this thread its just a line across the page when I print. I will re clean everything after the next print run.. read the file link and still cant upload the scanned pic.....
crappy little scanner.. there is a line across the page..sometimes every 10 or 20 prints.. now the attachments wont let me upload.. insert pic.. no go.. and my attachments are on.. I give up.
OK I will get the cannon scanner out of the parts shed.. to be continued...oh and be warned you may not like the print runs I do.. I'll do it in the afternoon.. Cheers.. and I do appreciate ..
do I have too.. its a long thin line that goes across the whole page sometimes the middle sometimes up top.. I do B&W print runs so its black.. I could draw the line for Ya... besides.. for some...
Hi,
I just replaced my transfer belt with a whole used assembly.. I checked it and cleaned and lubed everything... it looked good.. installed it on my 281c I do print runs of 500 at a time.. oh I...
Hi, a line 25mm wide all the way down the page of the landscape A4 print is visible like a roller ghosted... I have cleaned it all but it only helped a 50%... the line is coming back... any Ideas???
Thanks Jerryl,
I wish I could say that was the problem, but its fixed now.
Still it gave me a chance to service the machine. I'm an E-studio man now, I have divorced the Ricoh and am selling her...
Hi,
Does anyone have a toner compatibility list? eg.
T-3511D comparable with what other toners.
Thanks
Paul
Hi,
I have a 281c and it grinds on startup like at the back near the fuser then after it has warmed up every 1/2 minute it resets and the grind happens again.. then it stops until I print and it...
no build up. check the developer 1st and replaced.
OK so I have an estudio in my office now and I will post on that forum. as it makes a grinding noise when starting..
I'm over the ricoh's.. ...
OK Thanks..
now all I need is buckets of 281c toner..
My decision is made.. you have been very helpful. Ebay.. ?? the answer...
Regards
Paul
Just about to put the machine in the shed. I have 3 x 281c Estudios. But little toner, whereas I have buckets of toner for the 2238c. Stuff this I need to do a print run today.. Ohh my back.. Toner...
No pulled it apart and went through every wire again. still the same copies a fading black and three 15mm lines on back page with horizontal cross match color pattern all very light.
I give up does...
Why not Max, I'll try anything twice. Tks..
Hi,
After I replaced the drum drive motor and the gears, a few copies later........
The black toner will not fill up the development unit. First sc393-01 came up development error.
Then I did a...
I've been using the service manual for 8 months now. Its all fairly straight forward, Though I did have to dismantle one machine to get the idea better.
Still the facts remain, there are ways to...
Yep I dids that alright, n she works like a dream. (had to adjust the colour) Thank God I buy theses machines for $5 humm. Still I know when the developers and toners run out, the oil I keep up every...
forget it I just did a memory clear and all is well.
TKS
Yes, IC..is there a way to make the "oil alert page " to have a value higher than 27.5. Say 90.0 that would be better. I use sp7-905-014.
There has to be a way to beat the system.
RE:
Hi,
The fuse, for the oil supply of the 2238c Ricoh. Where can I buy them? Or compatibles or does anyone know the part # I have a parts catalogue but it does not supply the fuse only the complete...
I was going to re-set the fuser oil, replace the fuse?. OK if I can find one. Thanks.
I've been a rebel all my life so I'm going to try it anyhow.
The hole is small and last time I spilled a bit this time I'm using a squeeze gun nozel and will pour in 50mm at a time, 400mm refill...
I have 3 of theses units (Ricoh 2238c) and use them as mass flyer printers. I dont want to blow any more fusers. But I do want to refill the oil units. I have the DIMETHYLPOLYSILOXANE all I want to...
thanks... ptrflrs.... I will next day off. It it square on the colour prints only the black n white copies seem to be out of line, I'll get back to you.. thanks again. cheers
yes the belt. No it was set correct on the page. b4 the belt was replaced.