Thanks, I'll have to look into that. My adjustments to the lower and upper limits did not work, I'm getting en error 20-0492, which is related to those readings.
Type: Posts; User: neoboy3000
Thanks, I'll have to look into that. My adjustments to the lower and upper limits did not work, I'm getting en error 20-0492, which is related to those readings.
Ok, so I found the controls in the service software to adjust the upper and lower toner target densities and have been playing with them a bit. I managed to get the prints to come out much darker...
Do you know if there is a software control for manually adding toner, or do I need to physically remove the dev ay and pour it in while turning the gears?
Ok, I'll give that a try. Thanks.
The only success I did see was when I changed developing assemblies it was normal but then faded. It is only in the black, yes. I'm not sure where the control is to adjust the toner amount, but I did...
Yes, I've been trying to read through it in regards to this issue.
Looking through settings for clues, found that the patch detection at ATR control - Lv 2 COPIER>DISPLAY>DENS-S-K - is reading at 542, but the value of the target - Lv2 COPIER>DISPLAY>DENS>D-K-TRGT -...
Swapped the writer, no change. Wondering if toner concentration has anything to do with it, since the problem seemed to follow the dev unit to the other machine. As if the mix inside of it wasn't...
OEM Toner
Have tried different drums and drum assemblies, including new ones - as I said I switched even the entire P-Kit from a working machine
I am looking again at the laser now, but yes, the...
Hi, folks - I've got a C7010VP that has weak black in the prints. I had swapped the entire PCB (1-1,1-2, and 1-3) rack to resolve a different issue, and have gone back over those one at a time to...
It wound up being the PCB 1-1 or 1-2, not sure which. I had a spare PCB 1-3 that I had tried before that didn't work, but I was able to take the whole PCB assembly from a recently acquired parts...
I did check the image on the ITB, I'm getting misregistered colors. I'm looking at the skew again as a sheet registration problem, I think the skew on the sheet is probably the registration rollers,...
Ok, so maybe not the P-Kit :/ The black developing unit was disengaged, but it somehow still passed the color registration adjustment. When I re-engage the dev unit black is still trailing more than...
Problem with the drag in the black seems to have been in the P-Kit, possibly something in the drum ay. Still investigating that, but swapping the whole K p-kit got rid of it and (for the first time...
I guess I haven't tried any other trays; we have a paper supply module, so no bypass, but I'll maybe try that to see if the skew changes. The black though is a problem elsewhere, as you can see in...
Update: That skew is present in all colors, and the black is offset towards the trail edge of the sheet. I inspected the drum encoder on K, it was warped so I replaced it with a spare. Cause no...
Hey, all - long time no update. I was able to get an entire P-kit from a spare machine and install it in the M, which cleared up the issue with the magenta not imaging all the way to the front side....
I swapped the entire magenta P-kit with the other 7010 in the shop and the magenta prints all the way across, so it's definitely in that part of the machine (though I still was unable to complete the...
Sorry for the long quiet. I had a broken drum potential harness (on Magenta of course) that I had to replace, and now I am having another issue. I did measure the skew motors for Y and M and both...
Yeah, the torque limiter and the transmission shaft were a couple of the parts I spent time waiting for :( I did try following the workflow procedures, no luck. I have the machine a bit apart right...
Thanks for the all info, I really appreciate it.
I did follow the procedure when I swapped the laser unit between M and Y. The issue originally manifested in the middle of running 200 sheets of...
Hi - I have some registration issues on a iPRC7010, and I noticed that the magenta is not imaging on the near-side patches during the AT-IMG-X registration adjustment. Under closer inspection, the...
That did it, thank you very much for your help. It really is appreciated. :D:D:D:D:D:D:D:D:D:D
I am trained to repair this model (and have been for five years on this model, and for ten on our half dozen black and white Canon machines), and have the parts and service catalogs that don't list...
Ran into a C7010VP that wants the login for system manager, but I can't recall and can't find the default login in any of my materials. Anybody know the default, or if there is a way to bypass/reset...