Happy to be of assistance mate.
Cliff.
Type: Posts; User: canonbundy
Happy to be of assistance mate.
Cliff.
Hi, I've been away for a while however the fix for E027-0X00 (providing dev couplings etc are ok) is to remove the Hopper seals on not only the offending colour but the other 3 also, as they in turn...
Thanks for the prompt reply JPiek, it appears to be a Driver /I.T./IP issue, apparently the school have recently had Server updates & is printing ok using xover cable - will let you know the final...
We have an LBP7780 which displays DOOR OPEN when attempting to print & will not print but only on the PCs & is not displayed on the machine or from the internal m/c website - internal prints such as...
You definately do NOT have genuine oem Toner in the Hopper or the previous toner was not oem - cost us thousands to find out - oem 45/46 toner comes with the bottle in a plastic sleeve OPEN on BOTH...
I haven't had much to do with ipfs however a need to install Waste Ink Absorber boxes has arrived, there doesn't seem to be anything in the manual for this - just wondering how difficult it may be -...
If not the Fixing Drive Assy as Canuck suggested then check the free movement of the Fuser Cooling Fan F7 (behind Fixing Unit) - bushings can be lubed with light oil.
Jam code? Exit could mean Fuser, 3Way Unit or Finisher.
Thanks for that hidius, I will check it out when I get back from the Bush:rolleyes:.
Cliff.
Thanks for the quick response disam, I will check the Manual again - it makes sense ......in a way......but I preferred it after we installed the Cassette Heaters in the earlier machines that they...
It's going back a while for me but I think it is the Main Charge Corona Cleaner not making home position - does it make a gear grinding noise? If so, try pushing the Charger in, as the gears wear and...
Other than the switch on the lower r/h side of the machine to turn the environment switch on for the Cassette Heaters, does anyone know if there is a Service Mode switch? As all the Units we have (in...
Maybe clean 2nd t/fer roller & its housing.
Guessing you can't get into Service Mode to check and clear an error - Fixing Unit etc, before the mc shuts down? If not.
Try cleaning the contacts of ALL the PCBs, RAM etc in the Controller Box...
Eatmorechips is absolutely correct - the grease inside the Fixing Film/Element has dried out, which usually occurs with low volume usage, the Film & Element (if not worn/damaged) can be cleaned with...
As above then power off / power on.
Could be a fixing unit error - turn on & check error history then clear error - PO/PO & post the result.
Which tray doesn't lift & do the other trays lift?
I gotta say, I have 2 Units side by side in a school which have done in excess of 2M prints without changing the ETB or Drum Blades ......... unreal by the sounds of the Posts - however I do have the...
Seen it before - is it OEM Toner - hard lumps in Dev Unit? Replace with correct Toner- run skyshots (to deplete Hopper of old Toner) then replace Dev Unit. Then run Dev as a new install then full...
And did the Bottle turn??? OEM Toner???
There is a slotted coupling at the rear of the Orange Bottle housing which wears causing the Bottle not to turn even though the Drive is still turning -...
I would clean the Optics, Laser Glasses & Patch Detect Sensors then perform a full Autograd - assuming the Drum & ITB Units are good.
Maybe try White Level adjustment, SRV MODE - COPIER - FUNCTION - CCD - WTLV1 & WTLV2. Highlight WTLV1 place an A3 sheet on Platen Glass - ok, then highlight WTLV2 then place an A3 sheet in Doc...
Clean, reseat all contacts/connectors, addon pcbs, format/replace HDD - reinstall F/Ware:confused::confused:
Sounds like feed clutch/solenoid is sticking causing pickup rollers to turn continuously.