Mattel Strange Change Machine. They could NEVER make this today. It was a little domed oven that came with plastic blocks that were actually compressed monters. You put the block in and heated it up...
Type: Posts; User: Dave10
Mattel Strange Change Machine. They could NEVER make this today. It was a little domed oven that came with plastic blocks that were actually compressed monters. You put the block in and heated it up...
There is a sensor that looks at the neck of the bottle. It must be clean. We have re-used them, but we wash them out in our shop.
I just tried one to check and it worked. Firewall issue or something strange? Also, I don't mean to insult your intelligence but have to ask, did you hit SUBMIT at the bottom of the page?
I agree. Replace Cyan developer.
http://dnet-km.com/groupee_common/ver1.3.7.2147483647/platform_images/blank.gif
We have a 3500i with 16,000 copies on it. It's only been out for about 7-8 weeks, and about 3 weeks ago, they...
I used to work as a designer of electronics and mechanics for a toy company. We had a tiny transformer for an electro-luminescent toy. Put out 1500V. at a tiny current. The shock was safe but hurt...
I'll try this. Thanks all.
Thanks for the reply, Blackcat, but my problem is that I can't figure out how to send FRPO commands to the new 4500i. There is no method given in the manual, and I can't find it in the Command...
The Density on the new black and white machines seems really high to me. Very dark blacks and a lot of wasted toner. I can reduce copy density easily, but print density is a little more difficult....
Thanks for the response, but they have no monitoring program running. Settings seem okay.
We are having an intermittent scan problem with a C253. The IT person at the site says that the machine will be fine but suddenly , someone will try to scan and the machine will not connect. It just...
Yes, the drums are interchangeable.
I do it all the time. I just try to find the smallest one I can with all the same specs. Also, sometimes you can take them out of the machine and re-format on a computer and re-install. Works if it...
When this happens to me, I run all the refresh modes. Drum refresh, developer refresh, gray adjust, even, sometimes, AC calibration. It usually works.
It is the drums. I know you hate to hear it, but it is. I have had all 3 color drums go out on several of these. Supposedly, with the newer firmware, you can run the AC calibration in mode 3 or 4 and...
Every single time we have had this, it's because someone has added a new computer and the print driver port settings default to LPR. Change to RAW. Clear all print queues, and if necessary, change...
another thought, we have also seen on the "good" ones, even when it is full and the bladder seal does not pop off some machines will still not notify the user that the waste tank is full.
16396
So...anyone else having this issue? this was on a 3550ci. i think whoever designed this waste toner system needs to go back to school and rethink this. The rubber cap design, in my opinion...
The Zero-crossing error is never the board or the fuser. It's , and I've seen this probably 100 times, always from a power outage. When the power comes back on, the voltage is low and it causes the...
This is a continuation of an earlier post, but a new problem. I would like to know if you guys are having problems with these boards. I had to replace an engine board on a brand new machine because...
Got a call for doc feeder jamming this morning. Got there and found a teacher had tried to run a workbook through the feeder.
I am having a problem with a DP-M410 master misfeed. The master is wrapping around the Platen roller about 1 in 5 times. As of 3/21/12, all mod's have been installed and I updated firmware to ver...
We have a pretty new Duplo DP-m410, only 195k, with a master feed problem. It has less than 4k master count. Twice now, we have found about 2 1/2 feet of master wrapped around the platen roller....
We are having the same problem. Did you find a fix?
Hard to tell with the color of the belt being dark, but seems to look the same as the copies.