Search:

Thanks guys for digging up an old thread and posting a resolution. I have just had a MX4071 & FN29 start doing this and there seemed to be no info @ Sharp.
I will post an update after checking the...

Thanks for the replies mansart & easyrider

The issue is on the horizontal lines having a regular fadeout pattern as per 44111

Hi guys

Has anyone seen this: MX4070 scan quality has gone bad in the last 6 weeks, but copies are totally fine??

A 64-5 printout scanned in shows the horizontal lines fading in and out with a...

This is Gold mate! Cheers - no brackets on services reply - brackets on image send reply - doesn't hurt to have a sender name in image send as well.

Thanks for the replies

Update.. what was tried & what didn't work: dip sw touch screen adj, check display connectors again, another fresh sd card, psu pwb, scu pwb.

What did work: swap out...

Thanks Alpanapa - No not yet, definitely worth a crack though but it feels totally dead on the display - we touched all over and got no responses. Will have to get my magnifier out to see that...

Hi Guys

We have a 2640 that has a unresponsive touch screen. Home key still works, still prints etc. Unplugging power cycle doesn't help. Replacing SD card doesn't help. Reseating CF, MFP PWB,...

Update: Turns out the CN3 Cable at the MFP end had what looked like one connection peeled back on installation that may have shorted to the next and had taken out the MFP. Real hard to see even...

Hi Moose

Can you elaborate on what was wrong with the CN3 Cable into the LVDS PWB please?

I have just installed 6 MX2630's and it had to be the one that went up a flight of stairs that...

The charge rollers in the primary transfer belt unit can cause that sort of problem if they are dirty at the ends where the HV connections are - worth a crack?

I thought i was the only one in the...

Hi All

I am thinking about selling an MX7500 to one of our large print customers and haven't yet dabbled in this end of the Sharp lineup. Could some of you that have had issues with the model let...

Hi Guys, has anyone seen or fixed this problem? A school with a lot of access codes has a bizhub c350 and when they go to print out the access code usage it says printing and just sits there. ...

Hi guys, wondering if anyone has had this scenario...

Di-3510 replace drum and dev, reset drum and F8 no worries but the start button was flashing green. Oh well must have to turn off at main...

You need to turn off the hdd again. To do this you must remove the nic (which the hdd plugs into) and then turn on the m/c and go in and turn off the hdd. Then put the nic back in and all will be...

They have motors driving those rollers but they can be a bit funny depending on the firmware versions. The customer has noticed an slight arc mark on the top of the cover for the rear trans/sep...

Thanks Deep,

I did want to replace the rego rollers and sensors as a first port of call but it looks like i will have to get them on slow boat from japan.

I will look into some possible loop...

Be real careful to put the correct screws back in the lid that holds the web. The little short black screws are the ones you need there otherwise a longer screw will stop the gear turning and...

Haven't seen this problem since an old ep4050 did the same thing years ago and we never did find the cause.
Misfeeds at rego usually with a certain coloured paper but also with white now - But the...

If i can't make the damp paper thing fly... i gotta come back with parts! ... but if the customer is nice to me i'll fix it!

Oh, and that noise is normal! ... in fact your's is quieter than...

is it a mirror image or a repeat image?

675756 or ser4OCE! depending on what version you have. You can't really get into "service mode" with that though (you need to hook up with a laptop with an oce host license for that) but you can...

Same as on 7040's these switches are a big problem and cause all sorts of problems and can damage the psu as well. There is also a switch for the fuser handle closed pos'n that can cause these many...

Copier companies have to offset their lack of income from their primary business with a suplimentary secondary income source.

Most copier businesses are now just a front to legitemise their crack...

I keep saying to my customers to wait a little longer before deciding to purchase a new machine. Things keep getting cheaper and cheaper and it will be very soon we will be paying them for the...

Fosters is for export .....and teens on a budget!