Oh don't worry, the CR5 "BP Series" also does this
I have had many devices where I have had to change the developer due to it being all sucked out
It's becoming more of a problem as well
Type: Posts; User: Imprestik
Oh don't worry, the CR5 "BP Series" also does this
I have had many devices where I have had to change the developer due to it being all sucked out
It's becoming more of a problem as well
This issue is related to the MFP board 100%
We had to send back to Japan all CR4.5 MFP boards for repair and they returned them once fixed.
We sent back over 40 boards, they repaired most of...
How did you set these devices up when they were first installed?
I'm presuming you installed and configured 1 device and once it was working perfectly you cloned the rest?
If so blow the...
Only issue we have with this client is tearing the primary belt every 100K or so.
Most of there work is A5 booklets printed in B&W
I have escalated up to Japan and sent them a complete primary...
These devices are designed to be plugged in on separate circuits.
If both cables are connected on the one circuit this issue will always return.
Check to see if the client has setup 2 separate...
This issue has been resolved and rectified by Sharp Japan
Any waste toner box you have made before March 2023 will cause the L4-17,18,19 or 20 error code.
They found there was an issue with the...
No coronas on the BP series, now charge rollers so I doubt it will happen. In saying that I have a BP70C65 which has done almost 1.2million in a year and I haven't had it happen....
As stated above, the PTC housing is cracked and its arcing out.
Replace the PTC housing and you should be good to go
I have had a number of these only on the C55 and C65 series.
The brown drive gear wears out causing the noise. Very common issue at the moment
This is becoming and extremely common issue on the CR4 and CR4.5's
Its the MC electrode unit. The springs which touch the corona units to supply the corona units charge are starting to corrode or...
I would also recommend going down the BP series as well as most parts and firmware is the exact same.
Fusers are the same for B&W and colour and they all take the same parts as well
So if you...
I have this all the time
It's the fusing belt unit bearings on the MX602FB
For some reason they just don't last and I have never understood why...
swap the drum units around and see if the issue moves
All Sharp copiers collate no matter what option is installed.
I know on the Ricoh's the collate option is an extra which needs to be purchased unless a finisher is purchased with the...
Thats one of the first things I done with no success
I preformed toner patch setup via settings with the same result
You do realise then if this is what they want, almost all manufacturers can do this type of printing with the associated options connected to the device for this to happen so the statement above it...
I have had this recently on this model where paper had got under the scrapper plate and jammed around the fuser belt.
When I cleaned the fuser up the exact same jam was registering
When I...
Clean the connector on both the fuser and main frame with contact cleaner.
There is a bulletin for this where they provide you with cotton tips to clean the connectors.
I have found giving both...
The Sharp MX8090N does edge to edge with a fiery.
I have one client that does it.
In saying this and as mentioned above, you can not print edge to edge from lead to trail, you will need to trim
I have replaced an entire unit once which hasn't resolved the issue
It's got something to do with the workload
As stated, majority of the work is A5 booklets and I know there was a firmware fix...
Hey all,
Just wondering if anyone has been experiencing this in the field.
I have a client with a BP70C65. The device has just clicked over 500,000 clicks so it gets a workout. Device has been...
Is the fiery correctly patched in the required sequence?
Had a lot of this issue on various Ricoh production devices. Patches usually resolve the issue
Either way, none of this is clearly happening hence the issue. As one of the other techs have mentioned and I agree with him, there is a design floor in the MX601HB. What I can't work out is if its a...
That doesn't make sense...
Why would you have separate sections in the waste toner box for toner and developer?
My understanding is as the box fills up, the window starts to fill with waste, as...